WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) Only Wireless Control Function is Inoperative

DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM


  1. for 12 Pin Type

    B001FEZE02

  2. except 12 Pin Type, for 5L-E

    B001DQYE01
    *a from Battery
    *b Door Control Receiver
    *c Unlock Warning Switch Assembly
    *d Main Body ECU (Multiplex Network Body ECU)

  3. except 12 Pin Type, except 5L-E

    B001FEZE03

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following procedure.

  • When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

    Click here

  • It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.

    for Initialization:

    Click here

    for Registration:

    Click here

  • for 12 Pin Type:

    When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

  • for 12 Pin Type:

    First, confirm that there are no malfunctions in the tire pressure warning system. Refer to the How to Proceed with Troubleshooting procedure.

    Click here

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. Check the power door lock operation.

      Click here

      Result
      Proceed to
      Locked doors unlock
      Locked doors do not unlock

    Locked doors do not unlock

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    Locked doors unlock

  2. CHECK KEY REMINDER WARNING SYSTEM


    1. Check that the key reminder warning buzzer operates properly.

      Click here

      Result
      Proceed to
      Key reminder warning buzzer operates properly
      Key reminder warning buzzer does not operates properly

    Key reminder warning buzzer does not operates properly

    GO TO KEY REMINDER WARNING SYSTEM Click here

    Key reminder warning buzzer operates properly

  3. CHECK DOOR CONTROL TRANSMITTER ASSEMBLY


    1. When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.

      Click here

      Result
      Result Proceed to
      Wireless door lock/unlock/back door open function operates properly with a known good door control transmitter assembly. A
      Wireless door lock/unlock/back door open function does not operate. B

    B

    CHECK WAVE ENVIRONMENT Click here

    A

  4. CHECK TRANSMITTER BATTERY (VOLTAGE)


    1. Remove the transmitter battery.

      Click here

    2. Inspect the transmitter battery capacity.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

    NG

    REPLACE TRANSMITTER BATTERY Click here

  5. CHECK WAVE ENVIRONMENT


    1. Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

      Tech Tips


      • When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Proceed to
      Wireless functions operate properly
      Wireless functions do not operate properly

    Wireless functions operate properly

    END (AFFECTED BY WAVE INTERFERENCE)

    Wireless functions do not operate properly

  6. SWITCH TO SELF-DIAGNOSTIC MODE


    1. B001DHHE36
      Interior Light Output
      *1 On
      *2 Off
      *3 T1: 0.25 seconds
      *4 T2: 0.5 seconds

      Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.

    5. Proceed to the next step in accordance with the prompts on the GTS screen.

    6. Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK SELF DIAGNOSTIC MODE


    1. Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

      B001I6ME50
      Result
      Result Proceed to
      Normal wave (light flash pattern) is output (A). A
      Unmatching recognition code is output (B). B
      No diagnostic outputs (C). C

    A

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    C

    CHECK DOOR CONTROL RECEIVER (RESPONSE) Click here

    B

  8. CHECK REGISTER RECOGNITION CODE


    1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

      Click here

      Result
      Proceed to
      Recognition code can be registered
      Recognition code cannot be registered

    Recognition code can be registered

    END (GO TO OPERATION CHECK)

    Recognition code cannot be registered

    GO TO STEP 13 Click here

  9. CHECK DOOR CONTROL RECEIVER (RESPONSE)


    1. Prepare the door control transmitter assembly from another vehicle.

    2. Press and hold down the door control transmitter assembly switch.

    3. Check that an unmatching recognition code is output.

      Result
      Proceed to
      Unmatching recognition code is output
      Unmatching recognition code is not output

    Unmatching recognition code is output

    REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

    Unmatching recognition code is not output

  10. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)


    1. B001FQPC43
      *a

      Front view of wire harness connector

      (to Door Control Receiver)

      for 12 Pin Type:


      1. Disconnect the door control receiver connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R41-12 (GND) - Body ground Always Below 1 Ω

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R41-7 (+B) - Body ground Always 11 to 14 V
    2. B001HCNC31
      *a

      Front view of wire harness connector

      (to Door Control Receiver)

      except 12 Pin Type:


      1. Disconnect the door control receiver connector.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition
        R26-1 (GND) - Body ground Always Below 1 Ω

      3. Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R26-5 (+B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  11. CHECK DOOR CONTROL RECEIVER (OUTPUT)


    1. for 12 Pin Type:


      1. B001II2C02
        *a

        Component with harness connected

        (Door Control Receiver)

        Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R41-4 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
        Ignition switch lock, all doors closed and door control transmitter assembly switch pressed

        Pulse generation

        (0 to 12 V)

    2. except 12 Pin Type:


      1. B001F6RC17
        *a

        Component with harness connected

        (Door Control Receiver)

        Measure the voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        R26-2 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
        Ignition switch lock, all doors closed and door control transmitter assembly switch pressed

        Pulse generation

        (0 to 12 V)
      Result
      Result Proceed to
      OK (for 12 Pin Type) A
      OK (except 12 Pin Type) B
      NG C

    B

    CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)) Click here

    C

    REPLACE DOOR CONTROL RECEIVER Click here

    A

  12. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the R41 door control receiver connector.

    2. Disconnect the G218 main body ECU (multiplex network body ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      R41-4 (RDA) - G218-16 (RDA) Always Below 1 Ω
      R41-5 (PRG) - G218-4 (PRG) Always Below 1 Ω
      R41-4 (RDA) or G218-16 (RDA) - Other terminals and body ground Always 10 kΩ or higher
      R41-5 (PRG) or G218-4 (PRG) - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  13. REPLACE DOOR CONTROL RECEIVER


    1. Temporarily replace the door control receiver with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  14. CHECK REGISTER RECOGNITION CODE


    1. Perform the registration procedure.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  15. CHECK DOOR CONTROL RECEIVER (OPERATION)


    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

      OK
      Doors can be locked and unlocked by the door control transmitter assembly.
      Result
      Proceed to
      OK
      NG

    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

  16. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))


    1. Disconnect the R26 door control receiver connector.

    2. Disconnect the G64*1 or G218*2 main body ECU (multiplex network body ECU) connector.


      • *1: for 5L-E

      • *2: except 5L-E

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for 5L-E:
      Tester Connection Condition Specified Condition
      R26-2 (RDA) - G64-26 (RDA) Always Below 1 Ω
      R26-3 (PRG) - G64-25 (PRG) Always Below 1 Ω
      R26-2 (RDA) or G64-26 (RDA) - Other terminals and body ground Always 10 kΩ or higher
      R26-3 (PRG) or G64-25 (PRG) - Other terminals and body ground Always 10 kΩ or higher
      except 5L-E:
      Tester Connection Condition Specified Condition
      R26-2 (RDA) - G218-4 (RDA) Always Below 1 Ω
      R26-3 (PRG) - G218-5 (PRG) Always Below 1 Ω
      R26-2 (RDA) or G218-4 (RDA) - Other terminals and body ground Always 10 kΩ or higher
      R26-3 (PRG) or G218-5 (PRG) - Other terminals and body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  17. REPLACE DOOR CONTROL RECEIVER


    1. Temporarily replace the door control receiver with a new or known good one.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  18. CHECK REGISTER RECOGNITION CODE


    1. Perform the registration procedure.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  19. CHECK DOOR CONTROL RECEIVER (OPERATION)


    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

      OK
      Doors can be locked and unlocked by the door control transmitter assembly.
      Result
      Proceed to
      OK
      NG

    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here