REAR DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   

   Text in Illustration

   *a	Lock	*b	Unlock
   *c	Component without harness connected (Rear Door Lock assembly LH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         
         

         • If the result is not as specified, replace the rear door lock assembly.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Switch Condition Specified Condition 6 (LSSR) - 9 (E) Unlock Below 1 Ω 6 (LSSR) - 9 (E) Lock 10 kΩ or higher

         
         

         • If the result is not as specified, replace the rear door lock assembly.

2. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   

   Text in Illustration

   *a	Lock	*b	Unlock
   *c	Component without harness connected (Rear Door Lock Assembly LH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L) Unlock Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL) Set Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL) Unset

         
         

         • If the result is not as specified, replace the rear door lock assembly.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Switch Condition Specified Condition 5 (LSSR) - 6 (E) Unlock Below 1 Ω 5 (LSSR) - 6 (E) Lock 10 kΩ or higher

         
         

         • If the result is not as specified, replace the rear door lock assembly.

3. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   

   Text in Illustration

   *a	Unlock	*b	Lock
   *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL) Lock Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L) Unlock

         
         

         • If the result is not as specified, replace the rear door lock assembly.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Switch Condition Specified Condition 6 (LSSR) - 9 (E) Unlock Below 1 Ω 6 (LSSR) - 9 (E) Lock 10 kΩ or higher

         
         

         • If the result is not as specified, replace the rear door lock assembly.

4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   

   Text in Illustration

   *a	Unlock	*b	Lock
   *c	Component without harness connected (Rear Door Lock Assembly RH)	-	-

   
   

   1. Check the door lock motor operation.

      
      

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK
         Measurement Condition Specified Condition Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL) Lock Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L) Unlock Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL) Set Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL) Unset

         
         

         • If the result is not as specified, replace the rear door lock assembly.

   2. Check the detection switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         Tester Connection Switch Condition Specified Condition 9 (LSSR) - 10 (E) Unlock Below 1 Ω 9 (LSSR) - 10 (E) Lock 10 kΩ or higher

         
         

         • If the result is not as specified, replace the rear door lock assembly.