METER / GAUGE SYSTEM OPERATION CHECK


  1. CHECK INDICATOR/WARNING LIGHT


    1. Check the following indicators and warning lights.

      Indicator/Warning Light Switch Condition Specified Condition
      Brake warning light Ignition switch off → ON Comes on for 3 seconds
      ABS warning light
      SLIP indicator light*1
      TRC OFF indicator light*1
      VSC OFF indicator light*1
      CRAWL indicator light*3
      Downhill assist control indicator light*4
      KDSS indicator light*5
      Eco driving indicator Light*6
      Oil maintenance warning light*2, *7
      OIL level indicator light*8, *9
      T-BELT indicator light*2, *10
      SEDIMENTER/FUEL FILTER indicator light*11
      SEDIMENTER indicator light*12
      SPEED LIMIT indicator light*13
      PCS indicator light*14
      PPS warning light*1, *15
      Master warning light*16
      BSM indicator light*17
      Headlight beam level control system warning light*18
      LED headlight warning light*18
      Tire pressure warning light*19
      Diesel particulate filter warning light*22
      SRS warning light Ignition switch off → ON Comes on for 6 seconds
      CHARGE warning light Ignition switch off → ON

      • Illuminates when ignition switch turned to ON

      • Turns off when engine started
      OIL PRESSURE warning light*1
      A/T OIL TEMP warning light*2, *6
      MIL
      SIL indicator light*20, *21

      • *1: w/ VSC

      • *2: for Analog Meter, Segment Display Type

      • *3: w/ CRAWL Control

      • *4: w/ Downhill Assist Control

      • *5: w/ Kinetic Dynamic Suspension System

      • *6: for Automatic Transmission

      • *7: for 1KD-FTV, Europe

      • *8: for 1KD-FTV, 1GD-FTV

      • *9: for 1GR-FE, Europe

      • *10: for 1KD-FTV, 5L-E

      • *11: w/ SEDIMENT/FILTER Warning Light

      • *12: w/ SEDIMENT Warning Light

      • *13: for Middle East

      • *14: w/ Pre-crash Safety System

      • *15: w/ Power Steering System

      • *16: except Analog Meter, Segment Display Type

      • *17: w/ Blind Spot Monitor System

      • *18: for LED Headlight

      • *19: w/ Tire Pressure Monitor System

      • *20: for Manual Transmission

      • *21: for Europe

      • *22: w/ DPF

  2. CHECK SPEEDOMETER


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List.

      If the result is not as specified, the speedometer may have a malfunction.

      Note

      Do not use worn, underinflated or overinflated tires as the speedometer reading will be inaccurate.

    5. Check the deflection width of the speedometer indicator.

    6. CHECK TACHOMETER


      1. Connect a tune-up tachometer and start the engine.

      2. Compare the test results with the tachometer indicator.


      • *: for Gasoline Engine

      If the result is not as specified, the tachometer may have a malfunction.

    7. CHECK METER/GAUGE


      1. Connect the GTS to the DLC3.

      2. Perform the Active Test Click here.

    8. CHECK WARNING/INDICATOR LIGHT


      1. Connect the GTS to the DLC3.

      2. Perform the Active Test Click here.

    9. CHECK MULTI-INFORMATION DISPLAY (for Analog Meter, Segment Display Type)


      1. Connect the GTS to the DLC3.

      2. Perform the Active Test Click here.

    10. CHECK MULTI-INFORMATION DISPLAY (except Analog Meter, Segment Display Type)


      1. Connect the GTS to the DLC3.

      2. Perform the Active Test Click here.