CYLINDER HEAD REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Thoroughly clean all parts to be assembled.

  • Before installing the parts, apply fresh engine oil to all sliding and rotating surfaces.

  • Replace all gaskets and oil seals with new ones.

PROCEDURE


  1. INSTALL STUD BOLT

    Tech Tips

    If a stud bolt is deformed or the threads are damaged, replace it.


    1. Install the stud bolts.

      Torque:
      for stud bolt A and D
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
      for stud bolt B
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }
      for stud bolt C
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }
      for stud bolt E
      26 N*m  { 265 kgf*cm, 19 ft.*lbf }
      A01XH65E01
      Text in Illustration
      *1 Stud Bolt A and B *2 Stud Bolt C
      *3 Stud Bolt D *4 Stud Bolt E
      *a Front Side *b Intake Manifold Side
      *c Cylinder Head Cover Side *d Exhaust Manifold Side

  2. INSTALL NO. 1 STRAIGHT SCREW PLUG

    Tech Tips

    If the No. 1 straight screw plug is corroded, replace it.


    1. Apply adhesive to the end of each No. 1 straight screw plug.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    2. Using a 6 mm hexagon wrench, install the No. 1 straight screw plugs.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
      A01XISLE01
      Text in Illustration
      *1 Adhesive - -

  3. INSTALL SEMICIRCULAR PLUG


    1. Remove any old seal packing (FIPG material).

    2. Apply seal packing to the semicircular plug as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note


      • The semicircular plug must be installed within 3 minutes after applying the seal packing.

      • Prevent seal packing from adhering to the camshaft thrust groove.

      A01XFR3E02
      Text in Illustration
      *1 Adhesive - -

    3. Install the semicircular plug to the cylinder head.

  4. INSTALL INTAKE VALVE STEM OIL SEAL


    1. A01XIT1E03

      Using SST, push in a new oil seal.

      SST
      09201-41020

  5. INSTALL EXHAUST VALVE STEM OIL SEAL


    1. Using SST, push in a new oil seal.

      SST
      09201-41020

  6. INSTALL INTAKE VALVE


    1. A01XDP5E02

      Install the valve, spring seat, compression spring and spring retainer.

    2. Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.

      SST
      09202-70020
      09202-00021
    3. A01XKUB

      Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.

      Note

      Be careful not to damage the valve stem tip.

  7. INSTALL EXHAUST VALVE

    A01XKV4E02

    1. Install the valve, spring seat, compression spring and spring retainer.

    2. Using SST, compress the compression spring and install the 2 valve spring retainer locks to the valve stem.

      SST
      09202-70020
      09202-00021
    3. A01XGT8

      Using a plastic-faced hammer, lightly tap the valve stem tip to assure a proper fit.

      Note

      Be careful not to damage the valve stem tip.