THROTTLE BODY INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repairs" after replacing the throttle body with motor assembly Click here.

PROCEDURE


  1. INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the throttle body with motor assembly Click here.


    1. B001CGNE04
      Text in Illustration
      *a Protrusion
      *b Groove

      Install a new gasket to the intake manifold.

      Tech Tips

      Align the protrusion of the gasket with the groove of the intake manifold.

    2. Install the throttle body with motor assembly with the 4 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    3. Connect the water by-pass hose to the throttle body with motor assembly, and slide the clip to secure the hose.

    4. Connect the No. 2 water by-pass hose to the throttle body with motor assembly, and slide the clip to secure the hose.

    5. Connect the throttle body with motor connector.

  2. INSTALL INTAKE AIR CONNECTOR


    1. Install the intake air connector with the 3 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Tighten the hose clamp.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    3. Connect the vacuum hose.

    4. Connect the No. 2 ventilation hose.

    5. Connect the vacuum hose to the air pressure sensor.

    6. Connect the air pressure sensor connector.

    7. Attach the wire harness and vacuum hose to the intake air connector.

  3. INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE


    1. B001FPLE03
      Text in Illustration
      *a Upper
      *b Front
      *c Matchmark

      Install the air cleaner cap sub-assembly with air cleaner hose and align its matchmark with the matchmark of the intake air connector as shown in the illustration.

    2. Tighten the hose clamp.

      Note

      Check that the air cleaner hose is securely installed.

    3. Attach the 4 clamps.

    4. Attach the 3 clamps and connect the intake mass air flow meter connector.

  4. ADD ENGINE COOLANT

    Click here

  5. INSPECT FOR COOLANT LEAK

    Click here

  6. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  7. INSTALL FRONT BUMPER COVER LOWER

    Click here

  8. PERFORM INITIALIZATION

    Note

    Perform the following procedure after replacing the throttle body with motor assembly or any throttle body components. The following procedure should also be performed if the throttle body with motor assembly is cleaned.


    1. Turn the ignition switch to ON without operating the accelerator pedal.

      Note

      If the accelerator pedal is operated, perform the above steps again.

    2. Connect the GTS to the DLC3 and clear the DTCs Click here.

    3. Perform "Inspection After Repairs" Click here.

    4. Start the engine, and check that the MIL is not illuminated and that the idle speed is within the specified range when the A/C is switched off after the engine is warmed up.

      Engine Idle Speed
      Condition Specified Condition
      A/C switched off 600 to 700 rpm

      Note


      • Be sure to perform this step with all accessories off.

      • Make sure that the shift lever is in N (neutral) or P.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Throttle Sensor Position. Fully depress the accelerator pedal and check that the value changes.

    6. Perform a road test and confirm that there are no abnormalities.