SFI SYSTEM, Diagnostic DTC:P0500

DTC Code DTC Name
P0500 Vehicle Speed Sensor

DESCRIPTION

Vehicles, which are equipped with ABS (Anti-lock Brake System), detect the vehicle speed using the skid control ECU (brake actuator assembly) and speed sensor. The speed sensor monitors the wheel rotation speed and sends a signal to the skid control ECU. The skid control ECU converts the wheel speed signal into a 4-pulse signal and transmits it to the ECM via the combination meter assembly. The ECM determines the vehicle speed based on the frequency of the pulse signal.

Tech Tips


  • Various systems use the vehicle speed signal distributed from the combination meter. Check all the components possibly related to speed signal.

  • A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter assembly.

    The signal is changed to a pulse signal at the transistor in the combination meter assembly. Each ECU controls the respective system based on the pulse signal.

  • If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems using the speed signal will not operate normally.

B001D1CE20
*1 Pulse Signal
*2 from Wheel Speed Sensor
*3 Skid Control ECU
*4 Combination Meter
DTC No. DTC Detection Condition Trouble Area
P0500 While vehicle being driven, no vehicle speed sensor signal transmitted to ECM (2 trip detection logic).

  • Open or short in speed signal circuit

  • Wheel speed sensor

  • Combination meter

  • ECM

  • Skid control ECU

MONITOR STRATEGY

Required Sensors/Components (Main) Vehicle speed sensor, Combination meter and Skid control ECU
Required Sensors/Components (Related) Park/neutral position switch, Transmission revolution sensor (Speed sensor NT), Engine coolant temperature sensor, Crankshaft position sensor and Throttle position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Automatic Transmission Models
Vehicle speed 9 km/h (6 mph) or higher
Transmission turbine speed 720 rpm or higher
Shift position D
Gear position 2nd or higher
Park/neutral position switch fail Not detected
Manual Transmission Models
Fuel-cut ON

TYPICAL MALFUNCTION THRESHOLDS

Automatic Transmission Models
Duration of the following condition 8 seconds or more
Vehicle speed sensor signal No pulse input
Manual Transmission Models
Duration of the following condition 4.5 seconds or more
Vehicle speed sensor signal No pulse input

CONFIRMATION DRIVING PATTERN

B001GAIE01

  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on [A].

  6. Start the engine.

  7. On the GTS, enter the following menus to check the fuel-cut status: Powertrain / Engine and ECT / Data List / Idle Fuel Cut.

  8. Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

  9. Decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

  10. Stop the vehicle.

  11. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].

  12. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  13. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  14. Input the DTC: P0500.

  15. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

WIRING DIAGRAM

B001G2XE11
*1 Skid Control ECU (Brake Actuator)
*2 Combination Meter

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (VEHICLE SPEED)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

    5. Drive the vehicle.

    6. Read the value displayed on the GTS.

      OK
      Vehicle speeds displayed on GTS and speedometer display are equal.

    OK

    CHECK INTERMITTENT PROBLEMS Click here

    NG

  2. CHECK COMBINATION METER SYSTEM


    1. Inspect the circuits that send vehicle speed signals to this system in the meter system Click here.

    2. During the inspection in the meter section, if there is an instruction to proceed to the next suspected area, proceed to the next step.


    NEXT

  3. CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER)


    1. Disconnect the ECM connector.

    2. Disconnect the combination meter connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G304-17 (+S) - G181-23 (SPD) Always Below 1 Ω

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - JUNCTION CONNECTOR)