ECD SYSTEM, Diagnostic DTC:P007C, P007D

DTC Code DTC Name
P007C Charge Air Cooler Temperature Sensor Circuit Low
P007D Charge Air Cooler Temperature Sensor Circuit High

DESCRIPTION

B001D6HE01
*1 (Fig. 1)
*2 Resistance kΩ
*3 Acceptable
*4 Temperature °C (°F)

The Intake Air Temperature (IAT) sensor detects the IAT after the intake air passes through the intercooler. A built-in thermistor in the sensor changes its resistance value according to the intake air temperature. The lower the intake air temperature, the higher the thermistor resistance value. The higher the intake air temperature, the lower the thermistor resistance value (See Fig. 1).

The sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the sensor from terminal THIA via resistor R. Resistor R and the sensor are connected in series. When the resistance value of the sensor changes in accordance with changes in the IAT, the potential at terminal THIA also changes. Based on this signal, the ECM corrects the fuel injection volume to improve driveability with a cold engine.

P007C
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second

Short in the intake air temperature sensor (turbo) circuit for 0.5 seconds.

(1 trip detection logic).

  • Short in intake air temperature sensor (turbo) circuit

  • Intake air temperature sensor (turbo)

  • ECM
P007D
DTC Detection Drive Pattern DTC Detection Condition Trouble Area
Engine switch on (IG) for 1 second

Open in the intake air temperature sensor (turbo) circuit for 0.5 seconds.

(1 trip detection logic)

  • Open in intake air temperature sensor (turbo) circuit

  • Intake air temperature sensor (turbo)

  • ECM
Related Data List
DTC No. Data List

P007C

P007D

 Intake Air Temp (Turbo)

Tech Tips


  • If DTC P007C or P007D is stored, the following symptoms may appear:


    • Misfire

    • Combustion noise

    • Black smoke

    • White smoke

    • Lack of power

WIRING DIAGRAM

B001G80E01
*a Engine Coolant Temperature Sensor

CAUTION / NOTICE / HINT

Note

After replacing the ECM, the new ECM needs registration (See page ) and initialization Click here.

Tech Tips

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE


  1. READ VALUE USING GTS (INTAKE AIR TEMPERATURE (TURBO))


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

    4. Read the value.

      OK
      Same as air temperature near intake manifold
      Result
      Result Proceed to
      -40°C (-40°F) A
      140°C (284°F) or higher B
      OK (same as air temperature near intake manifold) C

      Tech Tips


      • If there is an open circuit, the GTS indicates -40°C (-40°F).

      • If there is a short circuit, the GTS indicates 140°C (284°F) or higher.


    B

    READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS) Click here

    C

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

    A

  2. READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)


    1. B001CSDE02
      Text in Illustration
      *1 Intake Air Temperature Sensor (Turbo)
      *2 ECM
      *a

      Front view of wire harness connector

      (to Intake Air Temperature Sensor (Turbo))

      Disconnect the intake air temperature sensor (turbo) connector.

    2. Connect terminals 1 and 2 of the intake air temperature sensor (turbo) wire harness side connector.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG) and turn the GTS on.

    5. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

    6. Read the value.

      OK
      140°C (284°F) or higher

    7. Reconnect the intake air temperature sensor (turbo) connector.


    NG

    CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) Click here

    OK

  3. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO).


    1. Replace the intake air temperature sensor (turbo) Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  4. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)


    1. Disconnect the intake air temperature sensor (turbo) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C84-2 - C150-35 (THIA) Always Below 1 Ω
      C84-1 - C150-27 (ETHI) Always Below 1 Ω

    4. Reconnect the intake air temperature sensor (turbo) connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  5. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM.


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  6. READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)


    1. B001F68E06
      Text in Illustration
      *1 Intake Air Temperature Sensor (Turbo)
      *2 ECM

      Disconnect the intake air temperature sensor (turbo) connector.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG) and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Intake Air Temp (Turbo).

    5. Read the value.

      OK
      -40°C (-40°F)

    6. Reconnect the intake air temperature sensor (turbo) connector.


    NG

    CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM) Click here

    OK

  7. REPLACE INTAKE AIR TEMPERATURE SENSOR (TURBO)


    1. Replace the intake air temperature sensor (turbo) Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  8. CHECK HARNESS AND CONNECTOR (INTAKE AIR TEMPERATURE SENSOR (TURBO) - ECM)


    1. Disconnect the intake air temperature sensor (turbo) connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C849-2 or C150-27 (THIA) - Body ground and other terminals Always 10 kΩ or higher

    4. Reconnect the intake air temperature sensor (turbo) connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR Click here

    OK

  9. REPLACE ECM


    1. Replace the ECM Click here.


    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED Click here

  10. REPAIR OR REPLACE HARNESS OR CONNECTOR


    1. Repair or replace the harness or connector.


    NEXT

  11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the GTS to the DLC3.

    2. Clear the DTCs Click here.

    3. Turn the engine switch off for 30 seconds or more.

    4. Turn the engine switch on (IG) for 1 second.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Confirm that the DTC is not output again.


    NEXT

    END