FUEL SYSTEM PRECAUTION


  1. IGNITION SWITCH EXPRESSION


    1. The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.

      Expression Ignition Switch (Position) Engine Switch (Condition)
      Ignition Switch off LOCK Off (Lock)
      Ignition Switch ACC ACC On (ACC)
      Ignition Switch ON ON On (IG)
      Engine Start START On (Start)

  2. PRECAUTION


    1. Before starting work on the fuel system, including inspections and repairs, disconnect the cable from the negative (-) battery terminal.

    2. Do not smoke or work near fire when performing work on the fuel system.

    3. Keep gasoline away from rubber or leather parts.

  3. DISCHARGE FUEL SYSTEM PRESSURE

    CAUTION:


    • Take precautions to prevent gasoline from spilling out before removing fuel system parts.

    • Pressure still remains in the fuel lines even after performing the following procedures. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.


    1. Remove the circuit opening relay from the engine room relay block.

    2. Start the engine. After the engine stops, turn the ignition switch off.

      Tech Tips

      DTC P0171 (system to lean) may be stored.

    3. Check that the engine does not start.

    4. Remove the fuel tank cap and let the air out of the fuel tank.

    5. Disconnect the cable from the negative battery (-) terminal.

      Note


      • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. Reinstall the circuit opening relay.

  4. FUEL SYSTEM


    1. When disconnecting a high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.


      1. Disconnect the fuel pump tube.

      2. Drain any fuel remaining inside the fuel pump tube.

      3. To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.

      4. Put a container under the connection.

    2. B001GKRE05
      Text in Illustration
      *a OK
      *b NG

      Observe these precautions when removing and installing the fuel injector assemblies.


      1. Never reuse the O-ring.

      2. When installing a new O-ring to the fuel injector assembly, do not damage it.

      3. Coat new O-rings with spindle oil or gasoline before installation. Do not use engine oil, gear oil or brake oil.

    3. B001F10E03
      Text in Illustration
      *a O-Ring

      Install the fuel injector assembly to the fuel delivery pipe and lower intake manifold as shown in the illustration.

      Note

      Before installing the fuel injector assembly, be sure to apply spindle oil or gasoline to the place where the fuel delivery pipe or cylinder head contacts the O-ring of the fuel injector assembly.

    4. Observe these precautions when disconnecting the fuel tube connector (for quick type A).


      1. B001G74E05
        Text in Illustration
        *a Fuel Hose Connector Cover

        Fuel Hose Connector Cover Type:

        Detach the lock claw by lifting up the cover as shown in the illustration.

      2. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.

      3. B001H4EE65

        If the connector and the pipe are stuck, pinch the connector, push and pull the pipe to disconnect the pipe and pull it out.

        Text in Illustration
        *a Retainer
        B001CHY Pinch
        B001DEF Pull

        Note


        • B001EX3E02

          Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

        • Do not use any tools to separate the pipe and connector.

        • Do not forcefully bend or twist the nylon tube.

        • Check for foreign matter on the pipe seal surface. Clean if necessary.

        • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

        • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

        Text in Illustration
        *a Retainer
        *b Nylon Tube
        *c Pipe
        *d O-Ring
        *e Fuel Tube Connector

      4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

      5. To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.

    5. Observe these precautions when connecting the fuel tube connector (for quick type A).


      1. Check that there is no damage or contamination in the connected part of the pipe.

      2. B001I4Y

        Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.

        Text in Illustration
        B001CHY Push
      3. B001CNW

        After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.

        Text in Illustration
        B001CHY Pull

      4. Fuel Hose Connector Cover Type:

        Attach the lock claws to the connector by pushing down on the cover.

      5. Check for any fuel leaks.

    6. Observe these precautions when disconnecting the fuel tube connector (for quick type B):


      1. Check if there is any dirt or mud on the pipe and around the connector before disconnecting them. Clean if necessary.

      2. Disconnect the parts by hand.

      3. B001GOE
        Text in Illustration
        *a Nylon Tube
        *b O-Ring
        *c Retainer
        *d Pipe

        If the connector and pipe are stuck, push and pull the connector to disconnect the pipe and pull it out.

        Text in Illustration
        B001CHY Turn
        B001DEF Pull

        Note


        • B001ECRE12

          Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

        • Do not use any tools to separate the pipe and connector.

        • Do not forcefully bend or twist the nylon tube.

        • Check for foreign matter on the pipe seal surface. Clean if necessary.

        • Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

        • If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.

      4. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.

      5. To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.

    7. Observe these precautions when connecting the fuel tube connector (for quick type B):


      1. B001F4G

        Align the axis of the connector with the axis of the pipe and push in the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of new engine oil to the tip of the pipe.

        Text in Illustration
        B001CHY Push
      2. B001CYB

        After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.

        Text in Illustration
        B001CHY Pull

      3. Check for fuel leaks.

    8. Observe these precautions when disconnecting the fuel tube connector (for quick type C).


      1. Check that there is no damage or foreign matter on the part of the pipe that contacts the connector.

      2. B001HK9E08

        Detach the 2 claws of the connector retainer. Push down on the connector and disconnect it from the pipe.

        Text in Illustration
        *a Retainer
        B001CHY Push
        B001DEF Down
        B001HIB Pull

        Tech Tips

        If the connector and pipe are stuck, pinch the fuel pipe by hand and push and pull the connector to disconnect it.

        B001EQOE16
        Text in Illustration
        B001CHY Pull
        B001DEF Push

        Note


        • B001D8AE14

          Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

        • Do not use any tools to separate the pipe and connector.

        • Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.

        • Check for any dirt and foreign matter on the pipe seal surface. Clean if necessary.

        • Do not forcibly bend, twist or turn the nylon tube.

        • Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the main tube.

        • If the pipe and connector are stuck together, pinch the tube between your fingers and turn it carefully to free it. Then disconnect the main tube.

        Text in Illustration
        *a Pipe
        *b Retainer
        *c Nylon Tube
        *d Connector
        *e O-Ring

      3. Check for foreign matter on the seal surface of the disconnected pipe. Clean it if necessary.

      4. To protect the disconnected pipe and connector from damage and foreign matter, cover them with a plastic bag.

    9. Observe these precautions when connecting the fuel tube connector (for quick type C).


      1. Check for foreign matter on the pipe and around the connector before connecting it. Clean it if necessary.

      2. B001EOZE10
        B001GZ3

        Align the axis of the connector with the axis of the pipe. Push the pipe into the connector, and then push up on the retainer.

        Text in Illustration
        *a Retainer
        B001CHY Up
        B001DEF Push

        Note


        • Before connecting the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

        • After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.

        Text in Illustration
        B001CHY Pull

    10. Observe these precautions when handling the nylon tube.

      Note


      • Be careful not to turn the connection part of the nylon tube and the quick connector when connecting them.

      • Do not kink the nylon tube.

      • Do not remove the EPDM protector on the outside of the nylon tube.

      • Do not bend the nylon tube as this may cause blockage.

    11. Observe these precautions when disconnecting the fuel tank breather tube connector:


      1. B001H5XE05

        Pinch the retainer and pull out the fuel tank breather tube connector with the fuel tank breather tube connector pushed toward the pipe to disconnect the fuel tank breather tube from the pipe.

        Text in Illustration
        *a Fuel Tank Breather Tube Connector
        *b Pipe
        B001CHY Push
        B001DEF Pinch

        Note


        • B001GK9E10

          Remove dirt or foreign objects on the fuel tank breather tube connector before performing this procedure.

        • Do not allow any scratches or foreign objects on the parts when disconnecting them as the fuel tank breather tube connector has the O-ring that seals the pipe.

        • Perform this work by hand. Do not use any tools.

        • Do not forcibly bend, kink or twist the nylon tube.

        • Protect the connecting part by covering it with a plastic bag after disconnecting the fuel tank breather tube.

        • If the fuel tank breather tube connector and pipe are stuck, push and pull them to release them.

        Text in Illustration
        *a Fuel Tank Breather Tube Connector
        *b Pipe
        *c Nylon Tube
        *d O-Ring

    12. Observe these precautions when connecting the fuel tank breather tube connector:


      1. B001CWI

        Align the fuel tank breather tube connector with the pipe, and then push in the fuel tank breather tube connector until the retainer makes a "click" sound to connect the fuel tank breather tube to the pipe.

        Text in Illustration
        B001CHY Push

        Note


        • Check that there are no scratches or foreign objects on the connected part of the fuel tank breather tube connector and pipe before performing this procedure.

        • After connecting the fuel tank breather tube, check that the fuel tank breather tube is securely connected by pulling the fuel tank breather tube connector.

      2. B001E6O

        After connecting the pipe and the connector, check that the pipe and connector are securely connected by trying to pull them apart.

        Text in Illustration
        B001CHY Pull

      3. Inspect for fuel leaks.

  5. INSPECT FOR FUEL LEAK

    Click here