BLACK OUT TAPE (for Rear Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01I3Q8

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01I52X

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01I63U

      Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides as shown in the illustration.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  6. REMOVE REAR ARMREST ASSEMBLY


    1. A01I4OW

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

  7. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01I5SVE02
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the rear door panel.

    2. A01I31I

      Remove the 3 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. A01I3NYE02
      Text in Illustration
      *1 Rear Door Inner Glass Weatherstrip
      *a Reference Boss

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. A01I2MY

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. A01I3L0E03
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

  8. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01I601E03
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  9. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01I57K

      Disconnect the connector.

    2. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.

    3. Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the rear door panel.

  10. REMOVE REAR DOOR CHECK ASSEMBLY


    1. A01I4VR

      Remove the bolt and 2 nuts, and rear door check assembly.

  11. REMOVE REAR DOOR WEATHERSTRIP


    1. A01I2FH

      Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.

  12. REMOVE REAR DOOR GLASS RUN


    1. A01I3EG

      Remove the rear door glass run.

  13. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01I4X3

      Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  14. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01I5GC

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  15. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01I28W

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  16. REMOVE REAR DOOR FRAME GARNISH


    1. A01I3RM

      Disengage the clip and remove the rear door frame garnish.

      Tech Tips

      This garnish needs to be replaced with a new one because the clip will break when removing it.

  17. REMOVE NO. 2 BLACK OUT TAPE


    1. Using a heat light, heat the No. 2 black out tape and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body and No. 2 Black Out Tape 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01I5MP

      Pull back on one of the ends of the No. 2 black out tape to remove it.

      Tech Tips

      When pulling on the No. 2 black out tape, pull it parallel to the body.

  18. REMOVE REAR DOOR OUTSIDE STRIPE


    1. Using a heat light, heat the rear door outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body and Rear Door Outside Stripe 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01I41H

      Pull back on one of the ends of the rear door outside stripe to remove it.

      Tech Tips

      When pulling on the rear door outside stripe, pull it parallel to the body.

  19. REMOVE REAR DOOR LOWER OUTSIDE STRIPE


    1. Using a heat light, heat the rear door lower outside stripe and vehicle body.

      Heating Temperature
      Item Temperature
      Vehicle Body and Rear Door Lower Outside Stripe 40 to 60°C (104 to 140°F)

      Note

      Do not heat the vehicle body excessively.

    2. A01I5DT

      Pull back on one of the ends of the rear door lower outside stripe to remove it.

      Tech Tips

      When pulling on the rear door lower outside stripe, pull it parallel to the body.