REAR BUMPER REASSEMBLY


  1. INSTALL REAR BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. A01I3IV

      Install the rear bumper reinforcement sub-assembly with the 6 nuts.

      Torque:
      61 N*m  { 622 kgf*cm, 45 ft.*lbf }

  2. INSTALL REAR BUMPER ENERGY ABSORBER


    1. A01I669

      Engage the 2 guides to install the rear bumper energy absorber.

  3. INSTALL REAR BUMPER SIDE SEAL LH


    1. A01I503

      Engage the guide and claw.

    2. A01I4MK

      Install the 2 screws.

    3. Install the rear bumper side seal LH with a new grommet.

  4. INSTALL REAR BUMPER SIDE SEAL RH


    1. A01I3E5

      Engage the guide and claw.

    2. A01I39E

      Install the 2 screws.

    3. Install the rear bumper side seal RH with a new grommet.

  5. INSTALL REAR BUMPER SIDE RETAINER LH


    1. A01I5FR

      Engage the 3 claws.

    2. Engage the 3 clips to install the rear bumper side retainer LH as shown in the illustration.

  6. INSTALL REAR BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  7. INSTALL REAR BUMPER LOWER COVER


    1. Engage the 2 guides and 10 claws.

      A01I40T
    2. A01I2AU

      Install the 2 clips.

    3. Install the rear bumper lower cover with the 2 outside moulding retainers.

  8. INSTALL NO. 2 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure for all No. 2 ultrasonic sensor retainers.


    1. A01I29AE01
      Text in Illustration
      *a Cutout
      *b Protrusion

      Engage the 2 claws to install the No. 2 ultrasonic sensor retainer to the rear bumper assembly.

      Note


      • Do not damage the rear bumper assembly with the protrusion when installing the No. 2 ultrasonic sensor retainer.

      • Securely install the No. 2 ultrasonic sensor retainer so that there are no gaps between the No. 2 ultrasonic sensor retainer and surface of the rear bumper assembly.

      Tech Tips


      • When installing the retainer, align the cutout and protrusion as shown in the illustration.

      • This illustration is for the LH side. The orientation for the RH side is the opposite of the LH side.

  9. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure for all No. 1 ultrasonic sensors.


    1. Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 2 ultrasonic sensor retainer.

      Note

      Push the No. 2 ultrasonic sensor retainer from the outside of the rear bumper assembly when there is a gap between the No. 2 ultrasonic sensor retainer and the rear bumper assembly surface. In this case, do not push on the No. 1 ultrasonic sensor.

  10. INSTALL ULTRASONIC SENSOR CLIP (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure for all ultrasonic sensor clips.


    1. Engage the 4 claws to install the ultrasonic sensor clip.

  11. INSTALL NO. 2 LUGGAGE ROOM WIRE (w/ Intuitive Parking Assist System)


    1. A01I2CL

      Connect the 4 connectors.

    2. Engage the 4 clamps to install the No. 2 luggage room wire.