FRONT DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. INSTALL FRONT DOOR BELT MOULDING ASSEMBLY


    1. A01I4AZ

      Engage the 5 claws to install the front door belt moulding assembly.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY


    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. for Driver Side:


      1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator master switch assembly.

    3. for Front Passenger Side:


      1. Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator switch assembly.

    4. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    5. A01I2Z3E03

      Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not the damage the front door glass sub-assembly.

    6. A01I4IL

      Install the front door glass sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    7. A01I2ZI

      Install the grommet.

  4. INSTALL NO. 2 FRONT DOOR SERVICE HOLE SEAL


    1. A01I4L2

      Install the No. 2 front door service hole seal.

  5. INSTALL NO. 1 FRONT DOOR SERVICE HOLE SEAL


    1. A01I2N4

      Install the No. 1 front door service hole seal.

  6. INSTALL FRONT DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the front door panel.

    2. A01I52RE02
      Text in Illustration
      *a Reference Point

      Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through a new front door service hole cover.

    3. Install the new front door service hole cover according to the reference points on the front door panel.

      Note

      Securely install the front door service hole cover preventing wrinkles and air bubbles.

    4. Engage the 5 clamps.

    5. Install the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    6. Connect each connector.

  7. INSTALL DOOR SIDE AIRBAG SENSOR


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01I2TUE01
      Text in Illustration
      *a Incorrect *b Correct

    4. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the door hole.

      • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. Connect the connector to the door side airbag sensor.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        A01I376E12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connection is Completed - -

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installation parts of the door side airbag sensor.

  8. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY

    Click here

  9. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  11. INITIALIZE POWER WINDOW CONTROL SYSTEM (for Driver Side)

    Click here

  12. INSPECT POWER WINDOW OPERATION

    Click here

  13. INSPECT SRS WARNING LIGHT

    Click here