LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

    Click here

  3. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01I5JDE01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  4. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01I2KI

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  5. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide LH.

    2. Disconnect the connector.

    3. A01I2G0

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  6. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I29Q

      Disengage the 10 claws and remove the front door scuff plate LH.

  7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  8. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01I3SV

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip.

  10. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A01I2SN

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  11. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01I5ER

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  12. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01I44B

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  13. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. A01I5U8

      Remove the 13 clips and luggage compartment door cover.

  14. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. A01I642

      Remove the 2 clips.

    2. Disengage the clip and remove the luggage compartment door hinge cover LH.

  15. REMOVE SPARE WHEEL COVER ASSEMBLY


    1. Remove the spare wheel cover assembly.

  16. REMOVE REAR FLOOR FINISH PLATE


    1. A01I5A2

      Remove the 5 clips.

    2. A01I344

      Disengage the 4 clips and remove the rear floor finish plate.

  17. REMOVE LUGGAGE COMPARTMENT FRONT TRIM COVER


    1. A01I3UH

      Disengage the 8 fasteners.

    2. Disengage the 3 claws and remove the luggage compartment front trim cover.

  18. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01I4J7E01
      Text in Illustration
      *a Pin

      Push the pin and remove the No. 1 luggage compartment trim hook.

  19. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01I2P6

      Remove the 2 clips.

    2. Disengage the 2 fasteners and remove the luggage compartment inner trim cover LH.

  20. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01I31P

      Remove the screw.

    2. A01I4XJ

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01I4EL

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  21. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01I3KW

      Disengage the 2 clamps.

    2. A01I4M4

      Using a clip remover, disengage the clamp and disconnect the wire harness.

    3. A01I2VY

      Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. A01I3KI

      Disengage the guide as shown in the illustration.

    6. A01I2Z7

      Disconnect the luggage door lock control cable sub-assembly.

    7. A01I46M

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. A01I5J5E02
      Text in Illustration
      *a Cutout
      *b Guide (A)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (A), and then pull the fuel filler opening lid lock retainer.

    9. A01I59JE02
      Text in Illustration
      *a Cutout
      *b Guide (B)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides (B), and then pull the fuel filler opening lid lock retainer.

    10. A01I28UE02
      Text in Illustration
      *a Cutout
      *b Guide (C)
      *c Guide (B)

      Pull out the fuel filler opening lid lock retainer with both guides (B) and (C) aligned with the cutouts.

    11. A01I5AO

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A01I3K7E01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    13. Using a knife, cut off the clamp as shown in the illustration.

      A01I4MQE02
      Text in Illustration
      *a Tape *b Cut

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.