OUTER REAR VIEW MIRROR INSPECTION

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH

1. Check the operation of the mirror surface (w/o Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 7 (M+) Turns upward Auxiliary battery positive (+) → Terminal 7 (M+) Auxiliary battery negative (-) → Terminal 3 (MV) Turns downward Auxiliary battery positive (+) → Terminal 6 (MH) Auxiliary battery negative (-) → Terminal 7 (M+) Turns left Auxiliary battery positive (+) → Terminal 7 (M+) Auxiliary battery negative (-) → Terminal 6 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly RH.

2. Check the operation of the mirror surface (w/ Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 6 (MV) Auxiliary battery negative (-) → Terminal 5 (M+) Turns upward Auxiliary battery positive (+) → Terminal 5 (M+) Auxiliary battery negative (-) → Terminal 6 (MV) Turns downward Auxiliary battery positive (+) → Terminal 4 (MH) Auxiliary battery negative (-) → Terminal 5 (M+) Turns left Auxiliary battery positive (+) → Terminal 5 (M+) Auxiliary battery negative (-) → Terminal 4 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly RH.

3. Check the operation of the retractable mirror (w/ Side Turn Signal Light).

   Note

   
   

   • Disconnect and reconnect the auxiliary battery between each mirror position check.

   • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

      OK

      Tester Connection Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Retracted position (E) Does not move Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

      If the result is not as specified, replace the outer rear view mirror assembly RH.

4. Check the operation of the mirror heater (w/ Mirror Heater and w/o Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (HR+) - 1 (HR-) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

   2. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 1, then check that the mirror becomes warm.

      Tech Tips

      It takes a short time for the mirror to become warm.

      OK
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.

5. Check the operation of the mirror heater (w/ Mirror Heater and Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly RH)

      Disconnect the outer rear view mirror assembly RH connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (HR+) - 11 (HR-) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly RH.

   3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 11, then check that the mirror becomes warm.

      Tech Tips

      It takes a short time for the mirror to become warm.

      OK
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly RH.

INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH

1. Check the operation of the mirror surface (w/o Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MV) Auxiliary battery negative (-) → Terminal 7 (M+) Turns upward Auxiliary battery positive (+) → Terminal 7 (M+) Auxiliary battery negative (-) → Terminal 3 (MV) Turns downward Auxiliary battery positive (+) → Terminal 6 (MH) Auxiliary battery negative (-) → Terminal 7 (M+) Turns left Auxiliary battery positive (+) → Terminal 7 (M+) Auxiliary battery negative (-) → Terminal 6 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly LH.

2. Check the operation of the mirror surface (w/ Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. Apply auxiliary battery voltage and check the operation of the mirror.

      OK

      Measurement Condition Specified Condition Auxiliary battery positive (+) → Terminal 6 (MV) Auxiliary battery negative (-) → Terminal 5 (M+) Turns upward Auxiliary battery positive (+) → Terminal 5 (M+) Auxiliary battery negative (-) → Terminal 6 (MV) Turns downward Auxiliary battery positive (+) → Terminal 4 (MH) Auxiliary battery negative (-) → Terminal 5 (M+) Turns left Auxiliary battery positive (+) → Terminal 5 (M+) Auxiliary battery negative (-) → Terminal 4 (MH) Turns right

      If the result is not as specified, replace the outer rear view mirror assembly LH.

3. Check the operation of the retractable mirror (w/ Side Turn Signal Light).

   Note

   
   

   • Disconnect and reconnect the auxiliary battery between each mirror position check.

   • The mirror position cannot be changed manually when the auxiliary battery is connected. To change the mirror position manually, the auxiliary battery must be disconnected first.

   
   
   1. 

      Text in Illustration

      *1	(A) Forward Position
      *2	(B)
      *3	(C) Driving position
      *4	(D)
      *5	(E) Retracted Position
      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. For each position: Disconnect the auxiliary battery, set the mirror position by hand, connect the auxiliary battery, and check the retractable mirror's movement.

      OK

      Tester Connection Condition Specified Condition Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Forward position (A) Moves from (A) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Forward position (A) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Position between forward position (A) and driving position (C) Moves from (B) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between forward position (A) and driving position (C) Moves from (B) to forward position (A) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Driving position (C) Moves from (C) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Driving position (C) Does not move Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Position between driving position (C) and retracted position (E) Moves from (D) to retracted position (E) Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Position between driving position (C) and retracted position (E) Moves from (D) to driving position (C) Auxiliary battery positive (+) → Terminal 3 (MR) Auxiliary battery negative (-) → Terminal 9 (MF) Retracted position (E) Does not move Auxiliary battery positive (+) → Terminal 9 (MF) Auxiliary battery negative (-) → Terminal 3 (MR) Retracted position (E) Moves from (E) to driving position (C)

      If the result is not as specified, replace the outer rear view mirror assembly LH.

4. Check the operation of the mirror heater (w/ Mirror Heater and w/o Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (HL+) - 1 (HL-) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.

   3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 1, then check that the mirror becomes warm.

      Tech Tips

      It takes a short time for the mirror to become warm.

      OK
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.

5. Check the operation of the mirror heater (w/ Mirror Heater and w/ Side Turn Signal Light).

   
   
   1. 

      Text in Illustration

      *a	Component without harness connected (Outer Rear View Mirror Assembly LH)

      Disconnect the outer rear view mirror assembly LH connector.

   2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 2 (HL+) - 11 (HL-) 25°C (77°F) 7.6 to 11.4 Ω

      If the result is not as specified, replace the outer rear view mirror assembly LH.

   3. Connect the cable from the positive (+) terminal to terminal 2 and the negative auxiliary battery (-) terminal to terminal 11, then check that the mirror becomes warm.

      Tech Tips

      It takes a short time for the mirror to become warm.

      OK
      Mirror becomes warm.

      If the result is not as specified, replace the outer rear view mirror assembly LH.