AIR CONDITIONING SYSTEM, Diagnostic DTC:B1498/98

DTC Code DTC Name
B1498/98 Communication Malfunction (A/C Inverter Local)

DESCRIPTION

The power management control ECU and compressor with motor assembly transmit information to one another via a communication line. Compressor control is stopped and the DTC is stored if communication information is cut off or abnormal information occurs.

The DTC is also detected if high-voltage power supplied from the inverter with converter assembly to the compressor control circuit is shut off.

The DTC will be stored as a history DTC.

DTC No. DTC Detection Condition Trouble Area
B1498/98

  • Communication line error or open between the power management control ECU and compressor with motor assembly.


  • High-voltage power source is shut off.

  • Harness or connector between power management control ECU, compressor with motor assembly and body ground

  • Power management control ECU

  • Compressor with motor assembly

  • No. 4 engine wire (harness or connector between compressor with motor assembly and inverter with converter assembly)

  • Electric vehicle fuse

  • CAN communication system

  • Hybrid control system

WIRING DIAGRAM

A01I425E30

INSPECTION PROCEDURE

CAUTION:


  • Wear electrically insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Be sure to carry the removed service plug grip because other workers may install it by mistake.

  • Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  • The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the diagnosis procedure for the hybrid control system first if any DTCs from those systems are output simultaneously.

  • Depending on the timing of the power supply to the 12 V power supply circuit and high-voltage circuit when the power switch is turned on (READY), an abnormal information signal may be output, causing this DTC to be stored. If the output DTC is a code that was memorized in the past, check the fuses and wire harnesses. If there is no malfunction, clear the DTC.

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Using the Techstream to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output B

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK DIAGNOSTIC TROUBLE CODE


    1. Check if DTCs for the hybrid control system are output using the Techstream.

      Result
      Result Proceed to
      DTC is not output A
      Only DTC P3108 is output A
      DTCs other than P3108 are output B

    B

    GO TO HYBRID CONTROL SYSTEM Click here

    A

  3. CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - BODY GROUND)

    CAUTION:

    Do not disconnect the connector on the high-voltage side.


    1. Disconnect the E65 compressor with motor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E65-5 (GND) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY - IG CIRCUIT, GROUND)


    1. Turn the power switch on (IG).

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      E65-6 (IG1) - E65-5 (GND) Power switch on (IG) 11 to 14 V
      E65-6 (IG1) - E65-5 (GND) Power switch off Below 1 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)


    1. Disconnect the A39 power management control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E65-1 (CLK) - A39-16 (CLK) Always Below 1 Ω
      E65-2 (DIN) - A39-17 (ITE) Always Below 1 Ω
      E65-3 (DOUT) - A39-18 (ETI) Always Below 1 Ω
      E65-1 (CLK) - Body ground Always 10 kΩ or higher
      E65-2 (DIN) - Body ground Always 10 kΩ or higher
      E65-3 (DOUT) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT ELECTRIC VEHICLE FUSE

    CAUTION:

    Be sure to wear insulated gloves.


    1. Turn the power switch off.

    2. Remove the service plug grip Click here.

      CAUTION:

      Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.

      Note

      After removing the service plug grip, turning the power switch on (READY) may cause a malfunction. Do not turn the power switch on (READY) with the service plug grip removed.

    3. Remove the connector cover assembly Click here.

      Note

      Be sure to prevent foreign objects or water from entering the inverter with converter assembly.

    4. A01I4QKE02
      Text in Illustration
      *a Electric Vehicle Fuse

      Check that bolts A and B are tightened securely.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Item

      (Tester Connection)

      		 Condition Specified Condition

      Electric vehicle fuse

      (A - B)

      		 Always Below 1 Ω

    NG

    REPLACE ELECTRIC VEHICLE FUSE Click here

    OK

  7. INSPECT NO. 4 ENGINE WIRE

    CAUTION:

    Be sure to wear insulated gloves.


    1. Disconnect the No. 4 engine wire connector Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G1-1 (PE) - G2-1 (ACPE) Always Below 1 Ω
      G1-2 (PB) - G2-2 (ACPB) Always Below 1 Ω
      G1-1 (PE) - Body ground Always 10 kΩ or higher
      G1-2 (PB) - Body ground Always 10 kΩ or higher

    NG

    REPLACE NO. 4 ENGINE WIRE Click here

    OK

  8. REPLACE COMPRESSOR WITH MOTOR ASSEMBLY


    1. Replace the compressor with motor assembly Click here.

      Tech Tips

      Since the compressor with motor assembly cannot be inspected while it is removed from the vehicle, replace the compressor with motor assembly with a new or a known good one and check that the condition returns to normal.

    2. Check for the DTC.

      Result
      Result Proceed to
      DTC B1498/98 is not output A
      DTC B1498/98 is output B

    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

    END (COMPRESSOR WITH MOTOR ASSEMBLY WAS DEFECTIVE)