REAR AIRBAG SENSOR INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01I3QWE01
      Text in Illustration
      *a Correct *b Incorrect

    4. Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.

      A01I4ULE01
      Text in Illustration
      *1 White Housing Lock - -
      *a Slide - -
      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the side No. 2 airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the body hole.

      • Tighten the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.

    5. Connect the connector to the side No. 2 airbag sensor assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.

  2. INSTALL REAR SIDE SEATBACK ASSEMBLY


    1. Engage the hook to install the rear side seatback assembly LH.

    2. Install the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

    3. Connect the connector.

    4. Connect the rear seat outer belt to the rear seat shoulder belt guide LH.

  3. INSTALL REAR SEAT CUSHION LOCK HOOK


    1. A01I58V

      Engage the claw to install a new rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  4. INSTALL REAR SEAT CUSHION ASSEMBLY


    1. Place the rear seat cushion assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. A01I5UX

      Engage the 2 hooks of the seat cushion to the vehicle body as shown in the illustration.

    3. Confirm that the seat cushion is firmly installed.

      Note

      When installing the seat cushion, make sure that the seat belt buckles are not under the seat cushion.

  5. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  6. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  7. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  8. INSPECT SRS WARNING LIGHT

    Click here