SIDE AIRBAG SENSOR (for Front Side) INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. INSTALL DOOR SIDE AIRBAG SENSOR


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01I2TUE01
      Text in Illustration
      *a Incorrect *b Correct

    4. Insert the pin (stopper) into the door hole and install the door side airbag sensor to the front door panel with the bolt.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

      Note


      • If the door side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

      • When installing the door side airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

      • Make sure that the pin (stopper) is securely inserted into the door hole.

      • Tighten the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. Connect the connector to the door side airbag sensor.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.


      1. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        A01I376E12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connection is Completed - -

        Tech Tips

        When engaged, the white housing lock will slide. Be sure not to hold the white housing lock or part (A), as it may result in an insecure fit.

    6. Check that there is no looseness in the installation parts of the door side airbag sensor.

  2. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01I2GZE03
      Text in Illustration
      *1 Front Door Inside Locking Cable Assembly
      *2 Front Door Lock Remote Control Cable Assembly

      Connect the front door lock remote control cable assembly and front door inside locking cable assembly.

    2. Engage the clamp.

    3. A01I2HGE02
      Text in Illustration
      *a Reference Boss

      Engage the 4 claws and reference boss as shown in the illustration.

    4. A01I5OQ

      Engage the 10 clips to install the front door trim board sub-assembly.

    5. Install the 3 screws.

    6. Remove protective tape.

  3. INSTALL COURTESY LIGHT ASSEMBLY


    1. Connect the connector.

    2. A01I2E0E01
      Text in Illustration
      *A for LH Side
      *B for RH Side

      Engage the claw to install the courtesy light assembly.

  4. INSTALL FRONT ARMREST ASSEMBLY


    1. A01I2QY

      Engage the 2 guides, 3 clips and 7 claws to install the front armrest assembly.

  5. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. Connect each connector.

    2. A01I3J6

      Engage the 3 guides, 2 clips and 6 claws to install the power window regulator master switch assembly with front door armrest base panel.

  6. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. Connect each connector.

    2. A01I5FJ

      Engage the 3 guides, 2 clips and 6 claws to install the power window regulator switch assembly with front door armrest base panel.

  7. INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH


    1. A01I3TY

      Engage the 3 clips to install the front door lower frame bracket garnish.

  8. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01I56C

      Engage the 3 claws to install the front door inside handle bezel plug.

  9. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  10. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  11. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  12. INSPECT SRS WARNING LIGHT

    Click here