FRONT SEAT ASSEMBLY (for Manual Seat) REASSEMBLY


  1. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. Install the separate type front seat cushion spring assembly.

  2. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY


    1. Install the 2 front seatback hooks to the separate type front seatback spring assembly.

    2. A01I4NA

      Engage the 2 guides.

    3. Engage the 4 claws to install the separate type front seatback spring assembly.

  3. INSTALL FRONT SEATBACK FRAME SUB-ASSEMBLY


    1. Install the front seatback frame sub-assembly with the 4 bolts.

      Torque:
      45 N*m  { 459 kgf*cm, 33 ft.*lbf }

  4. INSTALL RECLINING CONTROL LEVER


    1. Install the reclining control lever with the bolt.

      Torque:
      15 N*m  { 153 kgf*cm, 11 ft.*lbf }

  5. INSTALL FRONT SEAT WIRE RH


    1. Connect each connector and engage each clamp to install the front seat wire RH.

  6. INSTALL OCCUPANT DETECTION ECU


    1. A01I47X

      Engage the claw to install the occupant detection ECU.

      Note

      If the occupant detection ECU has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the occupant detection ECU with a new one.

    2. Connect the 2 connectors.

      Note

      When installing the occupant detection ECU, be careful that the SRS wiring does not interfere with or is pinched between other parts.

  7. INSTALL UPPER NO. 3 SEAT TRACK COVER


    1. Engage the 2 claws to install the upper No. 3 seat track cover.

  8. INSTALL UPPER NO. 4 SEAT TRACK COVER


    1. Engage the 2 claws to install the upper No. 4 seat track cover.

  9. INSTALL REAR UPPER SEAT TRACK COVER LH


    1. Engage the 2 claws to install the rear upper seat track cover LH.

  10. INSTALL REAR UPPER SEAT TRACK COVER RH


    1. Engage the 2 claws to install the rear upper seat track cover RH.

  11. INSTALL FRONT UPPER SEAT TRACK COVER LH


    1. Engage the 2 claws to install the front upper seat track cover LH.

  12. INSTALL FRONT UPPER SEAT TRACK COVER RH


    1. Engage the 2 claws to install the front upper seat track cover RH.

  13. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH


    1. Engage the 2 claws to install the front seat lower cushion shield LH.

  14. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

    Tech Tips

    Perform the same procedure as for the LH side.

  15. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. A01I4HV

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    2. Engage the 2 fasteners.

  16. INSTALL FRONT SEAT AIRBAG ASSEMBLY

    CAUTION:


    • The nuts must not be reused.

    • Make sure that the front seatback frame sub-assembly or separate type front seatback spring assembly is not deformed. If it is, replace it with a new one.


    1. Install the front seat airbag assembly with 2 new nuts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Engage the 2 clamps.

  17. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. Engage the 4 claws to install the 2 front seat headrest supports.

    3. Engage the 2 hooks.

      CAUTION:


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after engaging the 2 hooks.

      • Engage the 2 hooks securely.

    4. Engage the 2 fasteners.

    5. Engage the hook.

  18. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. A01I4A5

      Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 12 new hog rings.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

  19. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type front seat cushion cover with pad.

    2. Engage each hook.

    3. A01I2HR

      Install the separate type front seat cushion cover.

    4. Engage the claw and 3 clamps to install the front seat airbag assembly wire harness.

  20. INSTALL FRONT SEAT INNER CUSHION SHIELD


    1. Install front seat inner cushion shield with the 2 screws.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  21. INSTALL FRONT SEAT CUSHION SHIELD


    1. Engage the 2 claws to install a new front seat cushion shield.

    2. Install the 2 screws.

      Torque:
      0.6 N*m  { 6 kgf*cm, 5 in.*lbf }

  22. CONNECT SEPARATE TYPE FRONT SEATBACK COVER


    1. Connect the 2 rubber bands of the separate type front seatback cover.

  23. INSTALL RECLINING ADJUSTER RELEASE HANDLE


    1. Engage the claw to install the reclining adjuster release handle.

  24. INSTALL SEAT ADJUSTER COVER CAP


    1. Install the 2 seat adjuster cover caps.

  25. INSTALL LOWER SEAT TRACK RAIL


    1. Install the lower seat track rail.

  26. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH


    1. A01I4HYE02
      Text in Illustration
      *a Protruding Part

      Install the front seat inner belt assembly RH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly RH to overlap the protruding part of the front seat adjuster.

    2. Engage the clamp.

    3. Connect the connector.