CENTER AIRBAG SENSOR ASSEMBLY REMOVAL


  1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  2. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I29Q

      Disengage the 10 claws and remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01I3JL

      Remove the clip.

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01I56B

      Disconnect the front door opening trim weatherstrip LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01I3Y0

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01I58G

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01I3QN

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01I3G4

      Remove the bolt <C> and screw <D> or <E>.

    2. A01I2DI

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01I30B

      Remove the 2 screws <D> or <E>.

    2. Open the lower instrument panel door.

    3. A01I2C7

      Remove the 3 screws <D> or <E>.

    4. A01I2W8

      Disengage the 2 clips and 3 guides.

    5. A01I36Y

      Disengage the clamp.

    6. Disengage the glove compartment light as shown in the illustration.

    7. Disconnect the connector and remove the lower instrument panel sub-assembly.

  10. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01I603

      Remove the 2 screws <C> or <D>.

    2. A01I3XG

      Disengage the 2 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  11. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01I5C4

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01I5MF

      Remove the screw <C> or <D>.

    3. A01I4A8

      Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.

  12. REMOVE CONSOLE BOX INSERT


    1. A01I3BZ

      Remove the screw <C> or <D>.

    2. A01I4BW

      Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.

  13. REMOVE FLOOR CARPET BRACKET LH


    1. A01I5HF

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  14. REMOVE FLOOR CARPET BRACKET RH


    1. A01I4Z3

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  15. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01I2T5

      Remove the clip and No. 1 console box duct.

  16. REMOVE AIRBAG SENSOR ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. A01I383

      Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.