AIRBAG SYSTEM, Diagnostic DTC:B1622/81, B1623/81, B1632/81, B1633/81, B1642/81, B1692/81, B1693/81

DTC Code DTC Name
B1622/81 Lost communication with Side Airbag Sensor RH
B1623/81 Side Airbag Sensor Assembly RH Initialization Incomplete
B1632/81 Lost Communication with Rear Airbag Sensor RH
B1633/81 Rear Airbag Sensor Assembly RH Initialization Incomplete
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
B1692/81 Lost Communication with Door Side Airbag Sensor RH
B1693/81 Door Side Airbag Sensor RH Initialization Incomplete

DESCRIPTION

The side collision sensor RH circuit (to determine deployment of the front seat airbag assembly RH, rear seat airbag assembly RH, curtain shield airbag assembly RH and front seat outer belt assembly RH) is composed of the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH.

The side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag and pretensioner should be deployed.

These DTCs are stored when a malfunction is detected for the side collision sensor RH circuit.

DTC No. DTC Detection Condition Trouble Area

B1622/81

B1623/81

B1632/81

B1633/81

B1642/81

B1692/81

B1693/81

  • The airbag sensor assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the side collision sensor RH circuit.


  • Side airbag sensor assembly RH malfunction

  • Side No. 2 airbag sensor assembly RH malfunction

  • Door side airbag sensor RH malfunction

  • Airbag sensor assembly malfunction

  • No. 2 floor wire

  • Front door wire RH

  • Side airbag sensor assembly RH

  • Side No. 2 airbag sensor assembly RH

  • Door side airbag sensor RH

  • Airbag sensor assembly

WIRING DIAGRAM

A01I4XUE07

INSPECTION PROCEDURE

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

PROCEDURE


  1. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1642 or 81 is output. A
      Current DTC B1623 or B1633 is output. B
      Current DTC B1692 or B1693 is output. C
      Current DTC B1622 or B1632 is output. D
      Current DTCs B1622, B1623, B1632, B1633, B1642, B1692, B1693 and 81 are not output. E

      Tech Tips


      • DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the power switch off and then to on (IG) again.

      • Codes other than current DTCs B1622, B1623, B1632, B1633, B1642, B1692, B1693 and 81 may be output at this time, but they are not related to this check.


    B

    CHECK HISTORY DTC Click here

    C

    CHECK CONNECTORS Click here

    D

    CHECK CURRENT DTC Click here

    E

    USE SIMULATION METHOD TO CHECK Click here

    A

  2. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly, side airbag sensor assembly RH, side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  3. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01I5YRE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - O11-3 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  4. CHECK NO. 2 FLOOR WIRE (SHORT)

    A01I53TE02
    Text in Illustration
    *1 Side Airbag Sensor Assembly RH
    *2 Airbag Sensor Assembly
    *3 No. 2 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly RH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - O11-3 (BBR-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  5. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01I53TE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
      O11-3 (BBR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  6. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01I53TE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - Body ground Always 1 MΩ or higher
      O11-3 (BBR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  7. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01I4U6E06
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - O11-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  8. CHECK NO. 2 FLOOR WIRE (SHORT)

    A01I2JAE03
    Text in Illustration
    *1 Side No. 2 Airbag Sensor Assembly RH
    *2 Side Airbag Sensor Assembly RH
    *3 No. 2 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly RH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - O11-2 (BCR-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  9. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01I2JAE03
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
      O11-2 (BCR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  10. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01I2JAE03
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - Body ground Always 1 MΩ or higher
      O11-2 (BCR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  11. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)


    1. A01I3M5E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the connectors that link the No. 2 floor wire and front door wire RH.

    2. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - O32-2 (BDR-) Always Below 1 Ω

    NG

    CHECK FRONT DOOR WIRE RH (OPEN) Click here

    OK

  12. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - O32-2 (BDR-) Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE RH (SHORT) Click here

    OK

  13. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
      O32-2 (BDR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    CHECK FRONT DOOR WIRE RH (SHORT TO B+) Click here

    OK

  14. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - Body ground Always 1 MΩ or higher
      O32-2 (BDR-) - Body ground Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE RH (SHORT TO GROUND) Click here

    OK

  15. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01I4M3E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the side No. 2 airbag sensor assembly RH, door side airbag sensor RH and airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1642 or 81 is output. A
      DTC B1647 or 82 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  16. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    1. A01I2RVE01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1642 or 81 is output. A
      DTC B1647 or 82 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  17. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. A01I2T2E01
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly RH

      Interchange the door side airbag sensor RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1642 or 81 is output. A
      DTC B1647 or 82 is output. B
      DTCs B1642, B1647, 81 and 82 are not output. C

      Tech Tips

      Codes other than DTCs B1642, B1647, 81 and 82 may be output at this time, but they are not related to this check.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.


    B

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  18. CHECK HISTORY DTC


    1. Check for history DTCs Click here.

      Result
      Result Proceed to
      History DTCs B1622 and B1632 are not output. A
      History DTC B1622 is output. B
      History DTC B1632 is output. C

      Tech Tips

      Codes other than history DTCs B1622 and B1632 may be output at this time, but they are not related to this check.


    B

    CHECK SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    A

  19. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1623 is output. A
      Current DTC B1633 is output. B

      Tech Tips

      Codes other than current DTCs B1623 and B1633 may be output at this time, but they are not related to this check.


    B

    CHECK CONNECTORS Click here

    A

  20. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the airbag sensor assembly and side airbag sensor assembly RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the airbag sensor assembly and side airbag sensor assembly RH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  21. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01I5YRE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Airbag Sensor Assembly)
      *b

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 17 (BBR+) and 18 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - O11-3 (BBR-) Always Below 1 Ω

    3. Disconnect the service wire from connector B.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  22. CHECK NO. 2 FLOOR WIRE (SHORT)


    1. A01I53TE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - O11-3 (BBR-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  23. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01I53TE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - Body ground Power switch on (IG) Below 1 V
      O11-3 (BBR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  24. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01I53TE02
      Text in Illustration
      *1 Side Airbag Sensor Assembly RH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-4 (BBR+) - Body ground Always 1 MΩ or higher
      O11-3 (BBR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  25. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01I4M3E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connector to the airbag sensor assembly.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1623 is output. A
      DTC B1628 is output. B
      DTCs B1623 and B1628 are not output. C

      Tech Tips

      Codes other than DTCs B1623 and B1628 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  26. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side airbag sensor assembly RH and side No. 2 airbag sensor assembly RH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  27. CHECK NO. 2 FLOOR WIRE (OPEN)


    1. A01I4U6E06
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *4 Service Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Using a service wire, connect terminals 4 (BCR+) and 3 (BCR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - O11-2 (BCR-) Always Below 1 Ω

    3. Disconnect the service wire from connector C.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  28. CHECK NO. 2 FLOOR WIRE (SHORT)

    A01I2JAE03
    Text in Illustration
    *1 Side No. 2 Airbag Sensor Assembly RH
    *2 Side Airbag Sensor Assembly RH
    *3 No. 2 Floor Wire
    *a

    Front view of wire harness connector

    (to Side Airbag Sensor Assembly RH)

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - O11-2 (BCR-) Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  29. CHECK NO. 2 FLOOR WIRE (SHORT TO B+)


    1. A01I2JAE03
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - Body ground Power switch on (IG) Below 1 V
      O11-2 (BCR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  30. CHECK NO. 2 FLOOR WIRE (SHORT TO GROUND)


    1. A01I2JAE03
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly RH
      *2 Side Airbag Sensor Assembly RH
      *3 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to Side Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O11-1 (BCR+) - Body ground Always 1 MΩ or higher
      O11-2 (BCR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  31. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01I4M3E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Connect the connector to the side No. 2 airbag sensor assembly RH.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1633 is output. A
      DTC B1638 is output. B
      DTCs B1633 and B1638 are not output. C

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  32. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    1. A01I2RVE01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1633 is output. A
      DTC B1638 is output. B
      DTCs B1633 and B1638 are not output. C

      Tech Tips

      Codes other than DTCs B1633 and B1638 may be output at this time, but they are not related to this check.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  33. CHECK CONNECTORS


    1. Turn the power switch off.

    2. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the connectors are properly connected to the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also check that the connectors that link the No. 2 floor wire and front door wire RH are properly connected.

      OK
      The connectors are properly connected.

      Tech Tips

      If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

    4. Disconnect the connectors from the side No. 2 airbag sensor assembly RH and door side airbag sensor RH. Also disconnect the connectors that link the No. 2 floor wire and front door wire RH.

    5. Check that the terminals of the connectors are not damaged.

      OK
      The terminals are not deformed or damaged.

    NG

    REPLACE WIRE HARNESS

    OK

  34. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (OPEN)


    1. A01I3M5E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Service Wire
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Connect the connectors that link the No. 2 floor wire and front door wire RH.

    2. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - O32-2 (BDR-) Always Below 1 Ω

    NG

    CHECK FRONT DOOR WIRE RH (OPEN) Click here

    OK

  35. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Disconnect the service wire from connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - O32-2 (BDR-) Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE RH (SHORT) Click here

    OK

  36. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO B+)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Connect the cable to the negative (-) auxiliary battery terminal.

    2. Turn the power switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
      O32-2 (BDR-) - Body ground Power switch on (IG) Below 1 V

    4. Turn the power switch off.

    5. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


    NG

    CHECK FRONT DOOR WIRE RH (SHORT TO B+) Click here

    OK

  37. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT (SHORT TO GROUND)


    1. A01I414E05
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *a

      Front view of wire harness connector

      (to Side No. 2 Airbag Sensor Assembly RH)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      O32-1 (BDR+) - Body ground Always 1 MΩ or higher
      O32-2 (BDR-) - Body ground Always 1 MΩ or higher

    NG

    CHECK FRONT DOOR WIRE RH (SHORT TO GROUND) Click here

    OK

  38. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. A01I2T2E01
      Text in Illustration
      *1 Door Side Airbag Sensor LH
      *2 Side No. 2 Airbag Sensor Assembly RH

      Connect the connectors to the side No. 2 airbag sensor assembly RH.

    2. Interchange the door side airbag sensor RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1692 or B1693 is output. A
      DTC B1697 or B1698 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the door side airbag sensor RH and LH to their original positions and connect the connectors.


    B

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

  39. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    1. A01I2RVE01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly RH

      Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Clear the DTCs stored in memory Click here.

    4. Turn the power switch off.

    5. Turn the power switch on (IG), and wait for at least 60 seconds.

    6. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1692 or B1693 is output. A
      DTC B1697 or B1698 is output. B
      DTCs B1692, B1693, B1697 and B1698 are not output. C

      Tech Tips

      Codes other than DTCs B1692, B1693, B1697 and B1698 may be output at this time, but they are not related to this check.

    7. Turn the power switch off.

    8. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    9. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  40. CHECK CURRENT DTC


    1. Check for current DTCs Click here.

      Result
      Result Proceed to
      Current DTC B1622 is output. A
      Current DTC B1632 is output. B

      Tech Tips

      Codes other than current DTCs B1622 and B1632 may be output at this time, but they are not related to this check.

    2. Turn the power switch off.


    B

    CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    A

  41. CHECK SIDE AIRBAG SENSOR ASSEMBLY RH


    1. A01I4M3E01
      Text in Illustration
      *1 Side Airbag Sensor Assembly LH
      *2 Airbag Sensor Assembly

      Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    2. Interchange the side airbag sensor assembly RH with LH and connect the connectors.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1622 is output. A
      DTC B1627 is output. B
      DTCs B1622 and B1627 are not output. C

      Tech Tips

      Codes other than DTCs B1622 and B1627 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  42. CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH


    1. A01I2RVE01
      Text in Illustration
      *1 Side No. 2 Airbag Sensor Assembly LH
      *2 Side Airbag Sensor Assembly RH

      Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    2. Interchange the side No. 2 airbag sensor assembly RH with LH and connect the connectors to them.

    3. Connect the cable to the negative (-) auxiliary battery terminal.

    4. Clear the DTCs stored in memory Click here.

    5. Turn the power switch off.

    6. Turn the power switch on (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      Result
      Result Proceed to
      DTC B1632 is output. A
      DTC B1637 is output. B
      DTCs B1632 and B1637 are not output. C

      Tech Tips

      Codes other than DTCs B1632 and B1637 may be output at this time, but they are not related to this check.

    8. Turn the power switch off.

    9. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    10. Return the side No. 2 airbag sensor assembly RH and LH to their original positions and connect the connectors.


    B

    REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY RH Click here

    C

    USE SIMULATION METHOD TO CHECK Click here

    A

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  43. CHECK FRONT DOOR WIRE RH (OPEN)


    1. A01I2VWE07
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Front Door Wire RH
      *4 No. 2 Floor Wire
      *5 Service Wire
      *a

      Front view of wire harness connector

      (to No. 2 Floor Wire)
      *b

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      Disconnect the front door wire RH connector from the No. 2 floor wire.

      Tech Tips

      The service wire has already been inserted into connector E.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JO1-1 (BDR+) - JO1-2 (BDR-) Always Below 1 Ω

    3. Disconnect the service wire from connector E.


    NG

    REPLACE FRONT DOOR WIRE RH

    OK

    REPLACE NO. 2 FLOOR WIRE

  44. CHECK FRONT DOOR WIRE RH (SHORT)


    1. A01I2GRE06
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Front Door Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to No. 2 Floor Wire)

      Disconnect the front door wire RH connector from the No. 2 floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JO1-1 (BDR+) - JO1-2 (BDR-) Always 1 MΩ or higher

    NG

    REPLACE FRONT DOOR WIRE RH

    OK

    REPLACE NO. 2 FLOOR WIRE

  45. CHECK FRONT DOOR WIRE RH (SHORT TO B+)


    1. A01I2GRE06
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Front Door Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to No. 2 Floor Wire)

      Disconnect the front door wire RH connector from the No. 2 floor wire.

    2. Connect the cable to the negative (-) auxiliary battery terminal.

    3. Turn the power switch on (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      JO1-1 (BDR+) - Body ground Power switch on (IG) Below 1 V
      JO1-2 (BDR-) - Body ground Power switch on (IG) Below 1 V

    NG

    REPLACE FRONT DOOR WIRE RH

    OK

    REPLACE NO. 2 FLOOR WIRE

  46. CHECK FRONT DOOR WIRE RH (SHORT TO GROUND)


    1. A01I2GRE06
      Text in Illustration
      *1 Door Side Airbag Sensor RH
      *2 Side No. 2 Airbag Sensor Assembly RH
      *3 Front Door Wire RH
      *4 No. 2 Floor Wire
      *a

      Front view of wire harness connector

      (to No. 2 Floor Wire)

      Disconnect the front door wire RH connector from the No. 2 floor wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      JO1-1 (BDR+) - Body ground Always 1 MΩ or higher
      JO1-2 (BDR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE FRONT DOOR WIRE RH

    OK

    REPLACE NO. 2 FLOOR WIRE