GLASS BREAKAGE SENSOR ECU REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01I3Q8

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  5. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure for the RH side and LH side Click here.

  6. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01I4RT

      Disconnect the front door opening trim weatherstrip RH.

  7. REMOVE INSTRUMENT SIDE PANEL RH


    1. A01I400

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01I5ZT

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  8. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01I2SP

      Disengage the 4 claws and 2 guides.

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  9. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01I3RL

      Remove the 3 bolts.

    4. A01I46L

      Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. A01I2DPE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  10. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01I30B

      Remove the 2 screws <D> or <E>.

    2. Open the lower instrument panel door.

    3. A01I2C7

      Remove the 3 screws <D> or <E>.

    4. A01I2W8

      Disengage the 2 clips and 3 guides.

    5. A01I36Y

      Disengage the clamp.

    6. Disengage the glove compartment light as shown in the illustration.

    7. Disconnect the connector and remove the lower instrument panel sub-assembly.

  11. REMOVE GLASS BREAKAGE SENSOR ECU


    1. Disconnect the connector.

    2. A01I2O7

      Remove the nut and glass breakage sensor ECU.