AUDIO AND VISUAL SYSTEM (w/ DVD Player) Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

The radio and display receiver assembly and roof console box assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.

Using this circuit, the radio and display receiver assembly sends power to the roof console box assembly (telephone microphone assembly), and the roof console box assembly (telephone microphone assembly) sends microphone signals to the radio and display receiver assembly.

WIRING DIAGRAM

A01I2IHE20

INSPECTION PROCEDURE

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System Click here.

PROCEDURE


  1. CHECK MICROPHONE (OPERATION CHECK)


    1. A01I5QN

      Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check Click here.

    2. When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

      OK
      Check result is normal.

    NG

    CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)) Click here

    OK

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

  2. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY))


    1. Disconnect the I67 radio and display receiver assembly connector.

    2. Disconnect the S12 roof console box assembly (telephone microphone assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I67-4 (MACC) - S12-14 (MACC) Always Below 1 Ω
      I67-5 (MIN+) - S12-13 (MCO+) Always Below 1 Ω
      I67-19 (MIN-) - S12-12 (MCO-) Always Below 1 Ω
      I67-6 (SNS2) - S12-15 (SNS2) Always Below 1 Ω
      I67-4 (MACC) - Body ground Always 10 kΩ or higher
      I67-5 (MIN+) - Body ground Always 10 kΩ or higher
      I67-19 (MIN-) - Body ground Always 10 kΩ or higher
      I67-18 (SGND) - Body ground Always 10 kΩ or higher
      I67-6 (SNS2) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT RADIO AND DISPLAY RECEIVER ASSEMBLY


    1. A01I5JRE03
      Text in Illustration
      *a

      Component with harness connected

      (Radio and Display Receiver Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I67-4 (MACC) - Body ground Power switch on (ACC) 4 to 6 V

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      I67-18 (SGND) - Body ground Always Below 1 Ω
      I67-19 (MIN-) - Body ground Always Below 1 Ω

    NG

    REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY Click here

    OK

  4. INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    1. Remove the roof console box assembly (telephone microphone assembly) Click here.

    2. A01I5W0E51
      Text in Illustration
      *a

      Component without harness connected

      (Roof Console Box Assembly (Telephone Microphone Assembly))

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      15 (SNS2) - 12 (MCO-) Always Below 1 Ω

    NG

    REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) Click here

    OK

  5. INSPECT ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY)


    1. Turn the power switch on (ACC).

    2. A01I40EE45
      Text in Illustration
      *a

      Component with harness connected

      (Roof Console Box Assembly (Telephone Microphone Assembly))

      Connect an oscilloscope to terminals 13 (MCO+) and 12 (MCO-) of the S12 roof console box assembly (telephone microphone assembly) connector.

    3. Check the waveform of the roof console box assembly (telephone microphone assembly) using the oscilloscope.

      Result
      Result Proceed to
      A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is output. A
      A waveform synchronized with the voice input to the roof console box assembly (telephone microphone assembly) is not output. B

    B

    REPLACE ROOF CONSOLE BOX ASSEMBLY (TELEPHONE MICROPHONE ASSEMBLY) Click here

    A

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here