SHIFT LEVER INSTALLATION


  1. INSTALL SHIFT LEVER SUPPORT


    1. A01I2EHE01

      Install the shift lever support to the vehicle body with the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  2. INSTALL LOWER SHIFT LEVER ASSEMBLY

    Note

    Check that the shift lever position sensor and shift lever are in neutral.


    1. A01I2KPE01

      Install the lower shift lever assembly to the shift lever support with the 4 bolts in the sequence shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

    2. Engage the 2 clamps.

    3. Connect the shift lock control ECU connector.

    4. A01I5MSE03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

      Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.

    5. Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.

    6. A01I41XE01
      Text in Illustration
      *1 Lock Piece

      Connect the end of the transmission control cable assembly to the lower shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    7. Push the lock piece into the adjuster case.

      Note


      • Check that the shift lever position sensor and shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

  3. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. Install the No. 1 console box duct to the lower shift lever assembly with the clip.

  4. INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET


    1. Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.

    2. Engage the guide.

  5. INSTALL FLOOR CARPET BRACKET LH


    1. Engage the 2 guides.

    2. Install the floor carpet bracket LH with the 2 clips.

  6. INSTALL CONSOLE BOX INSERT


    1. A01I4NQ

      Engage the guide and 2 clips as shown in the illustration.

    2. Install the console box insert with the screw <C> or <D>.

  7. INSTALL FRONT NO. 2 CONSOLE BOX INSERT


    1. A01I4BV

      Engage the guide and 2 clips as shown in the illustration.

    2. Install the front No. 2 console box insert with the screw <C> or <D>.

    3. Engage the 2 claws to connect the room temperature sensor.

  8. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Connect each connector.

    2. A01I60M

      Engage the guide and 2 clips as shown in the illustration.

    3. Install the upper console panel sub-assembly with the 2 screws <C> or <D>.

  9. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01I2NZ

      Connect the connector.

    2. Engage the glove compartment light as shown in the illustration.

    3. Engage the clamp.

    4. A01I54P

      Engage the guide and 2 clips.

    5. Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.

  10. INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01I5AYE01
      Text in Illustration
      *1 Airbag Connector
      *2 Airbag Connector Lock

      Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

    4. Push in the lock to install the airbag connector.

    5. Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.

    6. Install the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note

      Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

  11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. Connect the connector.

    2. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.

  12. INSTALL INSTRUMENT SIDE PANEL RH


    1. Engage the 3 guides.

    2. A01I515

      Engage the 4 claws to install the instrument side panel RH as shown in the illustration.

  13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01I3B3E01
      Text in Illustration
      *1 Alignment Mark (White)

      Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.

      Note

      After installation, check that the corners fit correctly.

  14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  15. INSTALL FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  16. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. Engage the 4 claws, 9 clips and 3 guides.

    2. Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.

  17. CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.

  18. INSTALL INSTRUMENT SIDE PANEL LH


    1. Engage the 3 guides.

    2. A01I4VL

      Engage the 4 claws to install the instrument side panel LH as shown in the illustration.

  19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01I4EUE01
      Text in Illustration
      *1 Alignment Mark (Yellow)

      Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.

      Note

      After installation, check that the corners fit correctly.

  20. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01I4EE

      Insert the 2 clips in the direction indicated by the arrows shown in the illustration to engage them.

    2. Install the cowl side trim sub-assembly LH with the clip.

  21. INSTALL FRONT DOOR SCUFF PLATE LH


    1. Engage the 10 claws to install the front door scuff plate LH.

  22. INSTALL REAR CONSOLE BOX ASSEMBLY

    Click here

  23. INSPECT SHIFT LEVER POSITION


    1. While moving the shift lever from the N position to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

    2. Put the vehicle into the READY-on state and check the following:


      1. When the shift lever is moved to the D position, the vehicle moves forward.

      2. When the shift lever is moved to the R position, the vehicle moves in reverse.

        Note

        The vehicle should not move when the shift position indicator is off.

  24. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  25. INSTALL LUGGAGE TRIM SERVICE HOLE COVER


    1. Engage the claw to connect the luggage trim service hole cover.

  26. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  27. INSPECT SRS WARNING LIGHT

    Click here