SHIFT LEVER REMOVAL


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01I3Q8

      Disengage the claw to remove the luggage trim service hole cover.

  3. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  4. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  5. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I29Q

      Disengage the 10 claws and remove the front door scuff plate LH.

  6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01I3JL

      Remove the clip.

    2. Pull the cowl side trim sub-assembly LH in the direction indicated by the arrow shown in the illustration to disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01I56B

      Disconnect the front door opening trim weatherstrip LH.

  8. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01I3Y0

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01I58G

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  9. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01I3QN

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01I3G4

      Remove the bolt <C> and screw <D> or <E>.

    2. A01I2DI

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  11. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure as for the LH side.

  12. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  13. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH


    1. A01I4RT

      Disconnect the front door opening trim weatherstrip RH.

  14. REMOVE INSTRUMENT SIDE PANEL RH


    1. A01I400

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01I5ZT

      Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.

  15. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY


    1. A01I2SP

      Disengage the 4 claws and 2 guides.

    2. Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.

  16. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    CAUTION:

    When storing the lower No. 2 instrument panel airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01I3RL

      Remove the 3 bolts.

    4. A01I46L

      Disengage the 3 claws to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When removing the lower No. 2 instrument panel airbag assembly, do not pull the airbag wire harness.

    5. A01I2DPE01
      Text in Illustration
      *1 Protective Tape
      *2 Airbag Connector
      *3 Airbag Connector Lock

      Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

    6. Disconnect the airbag connector to remove the lower No. 2 instrument panel airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

  17. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01I30B

      Remove the 2 screws <D> or <E>.

    2. Open the lower instrument panel door.

    3. A01I2C7

      Remove the 3 screws <D> or <E>.

    4. A01I2W8

      Disengage the 2 clips and 3 guides.

    5. A01I36Y

      Disengage the clamp.

    6. Disengage the glove compartment light as shown in the illustration.

    7. Disconnect the connector and remove the lower instrument panel sub-assembly.

  18. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01I603

      Remove the 2 screws <C> or <D>.

    2. A01I3XG

      Disengage the 2 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  19. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01I5C4

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01I5MF

      Remove the screw <C> or <D>.

    3. A01I4A8

      Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.

  20. REMOVE CONSOLE BOX INSERT


    1. A01I3BZ

      Remove the screw <C> or <D>.

    2. A01I4BW

      Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.

  21. REMOVE FLOOR CARPET BRACKET LH


    1. A01I5HF

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  22. REMOVE NO. 1 CONSOLE BOX MOUNTING BRACKET


    1. A01I2ZQ

      Disengage the guide.

    2. Remove the screw and No. 1 console box mounting bracket from the lower shift lever assembly.

  23. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01I3T5

      Remove the clip and No. 1 console box duct from the lower shift lever assembly.

  24. REMOVE LOWER SHIFT LEVER ASSEMBLY


    1. A01I5DW

      Disconnect the end of the transmission control cable assembly from the lower shift lever assembly.

    2. Disengage the 2 claws to disconnect the transmission control cable assembly from the lower shift lever assembly.

    3. A01I3Z6

      Disconnect the shift lock control ECU connector.

    4. Disengage the 2 clamps.

    5. A01I2KP

      Remove the 4 bolts and lower shift lever assembly from the shift lever support.

  25. REMOVE SHIFT LEVER SUPPORT


    1. A01I56P

      Remove the 4 bolts and shift lever support from the vehicle body.