RADIATOR REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work Click here.

  2. DRAIN COOLANT (for Engine)

    Note

    Do not remove the radiator cap sub-assembly or radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


    1. Loosen the radiator drain cock plug.

    2. Remove the radiator cap sub-assembly.

      A01I4G4E01
      Text in Illustration
      *1 Radiator Cap Sub-assembly *2 Radiator Drain Cock Plug

      Tech Tips

      Collect the coolant in a container and dispose of it according to the regulations in your area.

  3. REMOVE FRONT WHEEL OPENING EXTENSION PAD RH

  4. REMOVE FRONT WHEEL OPENING EXTENSION PAD LH

  5. REMOVE ENGINE UNDER COVER RH

  6. REMOVE ENGINE UNDER COVER LH

  7. REMOVE LUGGAGE TRIM SERVICE HOLE COVER


    1. A01I3Q8

      Disengage the claw to remove the luggage trim service hole cover.

  8. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  9. REMOVE FRONT BUMPER ASSEMBLY

    Click here

  10. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

  11. REMOVE INLET AIR CLEANER ASSEMBLY


    1. A01I41G

      Remove the 2 bolts and inlet air cleaner assembly.

  12. REMOVE NO. 5 INVERTER BRACKET


    1. A01I3ST

      Remove the 2 bolts and No. 5 inverter bracket.

  13. REMOVE RADIATOR RESERVE TANK ASSEMBLY


    1. A01I2VZ

      Disconnect the radiator reserve tank hose.

    2. Remove the 2 bolts and radiator reserve tank assembly.

  14. DISCONNECT NO. 1 RADIATOR HOSE


    1. A01I3PA

      Disconnect the No. 1 radiator hose.

  15. DISCONNECT NO. 2 RADIATOR HOSE


    1. A01I4HN

      Disconnect the No. 2 radiator hose and clamp.

  16. DISCONNECT NO. 1 INVERTER COOLING PIPE ASSEMBLY


    1. A01I5DV

      Remove the 2 bolts and disconnect the No. 1 inverter cooling pipe assembly.

  17. REMOVE HOOD LOCK ASSEMBLY


    1. A01I5NGE01
      Text in Illustration
      *a Protective Tape

      Using a screwdriver, remove the hood lock nut cap.

      Tech Tips

      Tape the screwdriver tip before use.

    2. w/ Engine Hood Courtesy Switch:


      1. A01I28M

        Disconnect the connector.

    3. A01I4YPE01
      Text in Illustration
      *1 Hood Lock Bolt

      Remove the 2 bolts and hood lock bolt.

    4. A01I362

      Disconnect the hood lock control cable assembly and remove the hood lock assembly.

  18. REMOVE UPPER RADIATOR SUPPORT


    1. A01I4YB

      Disconnect the 2 connectors.

    2. A01I5OO

      Disconnect the hood lock control cable clamp and remove the 5 bolts and upper radiator support.

    3. Remove the 2 radiator support cushions.

  19. REMOVE RADIATOR ASSEMBLY


    1. A01I2YQ

      Disconnect the 2 clamps.

    2. A01I2RJ

      Disconnect the 2 clamps and connector.

    3. A01I55X

      Disconnect the clamp and No. 4 inverter cooling hose.

    4. A01I50L

      Remove the 4 bolts and separate the condenser assembly from the radiator assembly (for inverter coolant).

    5. A01I2L4

      Remove the radiator assembly with the fan assembly.

      Note

      Do not apply any excessive force to the radiator assembly (for inverter coolant), cooler condenser assembly or pipe when removing the radiator assembly.

    6. Remove the 2 lower radiator supports.

    7. A01I46E

      Release the 3 claws and lift the fan assembly from the radiator.