FRAME WIRE REMOVAL


  1. REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

    Click here

  2. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01I5JDE01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  3. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01I2KI

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  4. REMOVE REAR SEATBACK ASSEMBLY RH


    1. Fold down the rear seatback assembly RH.

    2. A01I5UGE01
      Text in Illustration
      *1 Fastener

      Disengage the 3 fasteners as shown in the illustration.

    3. A01I5CT

      Remove the 2 bolts and rear seatback assembly RH.

      Note

      Be careful not to damage the vehicle body.

  5. REMOVE NO. 2 ROOM PARTITION COVER


    1. A01I55K

      Using a moulding remover, disengage the claw and guide, and remove the No. 2 room partition cover.

  6. REMOVE REAR SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat inner with center belt assembly LH from the rear seat center shoulder belt guide.

    2. A01I44X

      Pull the cable in the direction shown in the illustration to release the rear seatback lock and then fold the rear seatback assembly LH forward.

    3. A01I2RWE01
      Text in Illustration
      *1 Fastener

      Disengage the 2 fasteners as shown in the illustration.

    4. A01I2HA

      Remove the 2 bolts and rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  7. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat inner with center belt assembly LH from the rear seat center shoulder belt guide.

    2. A01I44X

      Pull the cable in the direction shown in the illustration to release the rear seatback lock and then fold the rear seatback assembly LH forward.

    3. A01I2RWE01
      Text in Illustration
      *1 Fastener

      Disengage the 2 fasteners as shown in the illustration.

    4. A01I2HA

      Remove the 2 bolts and rear seatback assembly LH.

      Note

      Be careful not to damage the vehicle body.

  8. REMOVE REAR SIDE SEATBACK ASSEMBLY RH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide RH.

    2. Disconnect the connector.

    3. A01I4LE

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly RH.

  9. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip LH.

  10. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP RH


    1. Disconnect the rear door opening trim weatherstrip RH.

  11. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for LH Side)


    1. A01I40P

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  12. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY (for RH Side)


    1. A01I3RA

      Remove the bolt and disconnect the floor anchor of the rear seat outer belt assembly.

  13. REMOVE CHILD RESTRAINT SEAT ANCHOR BRACKET SUB-ASSEMBLY LH


    1. A01I2AQ

      Remove the 2 nuts and child restraint seat anchor bracket sub-assembly LH.

  14. DISCONNECT REAR SEAT INNER WITH CENTER BELT ASSEMBLY LH


    1. A01I4I2

      Remove the bolt.

    2. Disengage the guide to remove the rear seat inner with center belt assembly LH.

  15. REMOVE ROOF SIDE INNER GARNISH LH


    1. A01I45H

      Disengage the 5 clips.

    2. Disengage the guide and remove the roof side inner garnish LH.

  16. REMOVE ROOF SIDE INNER GARNISH RH

    Tech Tips

    Use the same procedure as for the LH side.

  17. REMOVE CENTER STOP LIGHT SET


    1. A01I5YIE01

      Slide the center stop light set in the order and directions shown by the arrows in the illustration while pushing it towards the rear of the vehicle to disengage the 4 claws.

    2. A01I5QH

      Turn the center stop light set 180 degrees as shown by the arrow in the illustration.

      Tech Tips

      This makes it easier to disconnect the connector.

    3. Disconnect the connector and remove the center stop light set.

  18. REMOVE CHILD RESTRAINT SEAT TETHER ANCHOR COVER


    1. A01I3PJ

      Using a moulding remover, disengage the 2 claws and 2 guides to remove the child restraint seat tether anchor cover.

      Tech Tips

      Use the same procedure for the other 2 child restraint seat tether anchor covers.

  19. REMOVE REAR SEAT SHOULDER BELT COVER


    1. A01I3VK

      Using a moulding remover, disengage the 2 claws and 4 guides and remove the rear seat shoulder belt cover.

      Tech Tips

      Use the same procedure for the other 2 rear seat shoulder belt covers.

  20. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A01I5RTE01
      Text in Illustration
      *1 Protective Tape

      Using pliers, disengage the 3 clips from inside the luggage compartment as shown in the illustration.

      Tech Tips

      Tape the tip of the pliers before use.

    2. Disengage the 5 guides.

    3. Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly then remove the package tray trim panel assembly.

  21. REMOVE NO. 1 ROOM PARTITION BOARD


    1. A01I2QH

      Using a clip remover, remove the 4 clips.

    2. Disengage the 5 clips and remove the No. 1 room partition board.

  22. REMOVE NO. 1 FLOOR UNDER COVER


    1. A01I2XQ

      Remove the 2 bolts and screw.

      Text in Illustration
      A01I3Q9 Bolt
      A01I679 Screw
      A01I4CJ Nut (attached to under cover)

    2. Disengage the 3 nuts and 2 clips, and remove the No. 1 floor under cover.

  23. REMOVE FRONT CENTER FLOOR COVER RH


    1. A01I3DM

      Remove the 6 clips and front center floor cover RH.

  24. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY


    1. A01I34M

      Remove the nut and disconnect the No. 2 parking brake cable assembly.

  25. REMOVE NO. 4 HYBRID BATTERY SHIELD PANEL

    CAUTION:

    Wear insulated gloves.


    1. A01I4J1E01
      Text in Illustration
      *1 Service Plug Grip
      *2 Battery Cover Lock Striker
      *3 Button
      *a Projection
      *b Turn

      Using the service plug grip, remove the battery cover lock striker.

      Tech Tips

      Insert the projecting part of the service plug grip, and turn the button of the battery cover lock striker counterclockwise to release the lock.

    2. A01I2X9

      Remove the bolt, 2 nuts and No. 4 hybrid battery shield panel.

  26. REMOVE NO. 4 FLOOR WIRE

    CAUTION:

    Wear insulated gloves.

    Note

    Insulate the removed terminals with insulating tape.


    1. A01I641

      Disconnect the 2 connectors.

    2. Disconnect the shielded wire ground.

    3. A01I4QC

      Disconnect the wire harness clamp and connector.

    4. A01I5WW

      Disengage the 3 claws and push the frame wire out from the floor panel.

    5. A01I643

      Disconnect the 2 wire harness clamps.

    6. A01I3J3

      Disconnect the 2 wire harness clamps and connector.

    7. Remove the 2 nuts.

    8. A01I4FV

      Remove the 2 bolts.

    9. Remove the 2 bolts and 4 nuts.

      A01I3HI

    10. Disconnect the 2 clamps and remove the No. 4 floor wire.

      A01I3NV

      Tech Tips

      When removing the clamp, break the claw on the clamp. The clamp cannot be reused.