CYLINDER HEAD REASSEMBLY

Tech Tips

Perform "Inspection After Repair" after replacing the cylinder head sub-assembly Click here.

INSTALL SPARK PLUG TUBE
Tech Tips

When using a new cylinder head, the spark plug tubes must be replaced.
1. Apply adhesive onto the shaded area of a new spark plug tube.
  
  Adhesive
  
  Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.
  
  Standard application width
  
  1.0 to 3.0 mm (0.0394 to 0.118 in.)
  Note
  
  Install the spark plug tube within 3 minutes after applying adhesive.
  
  Be careful not to deform the spark plug tube.
  
  Be careful not to expose the seal to coolant for at least 1 hour after installing it.
2. Text in Illustration
  
  *a Cylinder Head Casting Surface
  
  Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
  
  Standard protrusion height
  
  112 mm (4.41 in.)
  
  Note
  
  To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.
INSTALL CYLINDER HEAD STUD BOLT
1. Using an E7 "TORX" socket wrench, install the 5 cylinder head stud bolts.
  
  Torque:
  
  9.0 N*m { 92 kgf*cm, 80 in.*lbf }
INSTALL NO. 1 STRAIGHT SCREW PLUG
1. Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.
  
  Torque:
  
  44 N*m { 449 kgf*cm, 32 ft.*lbf }
INSTALL NO. 2 STRAIGHT SCREW PLUG
1. Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.
  
  Torque:
  
  78 N*m { 795 kgf*cm, 58 ft.*lbf }
INSTALL VALVE SPRING SEAT
1. Install the valve spring seats to the cylinder head.

Adhesive
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent.

Standard application width
1.0 to 3.0 mm (0.0394 to 0.118 in.)

Text in Illustration
*a	Cylinder Head Casting Surface

Standard protrusion height
112 mm (4.41 in.)

INSTALL VALVE STEM OIL SEAL

Apply a light coat of engine oil to new oil seals.

Text in Illustration
*A	for Intake Side	*B	for Exhaust Side
*a	Gray (for Intake Side)	*b	Black (for Intake Side)
*c	Black (for Exhaust Side)	*d	Gray (for Exhaust Side)

Note

Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal onto the exhaust side or installing the exhaust oil seal onto the intake side can cause installation problems later.

Tech Tips

for Intake Side

The intake side valve stem oil seals is gray or black.
for Exhaust Side

The exhaust side valve stem oil seals is black or gray.

Text in Illustration

*a CORRECT

*b INCORRECT

Using SST, push in the intake and exhaust valve oil seals.

SST

09201-41020

Note

Failure to use SST will cause the seal to be damaged or improperly seated.

INSTALL INTAKE VALVE
1. Text in Illustration
  
  *a 30 mm (1.18 in.) or more
  
  Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.
2. Install the intake valve, compression spring and valve spring retainer to the cylinder head.
  
  Note
  
  Install the same parts in the same combination to their original locations.
3. Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.
  
  SST
  
  09202-70020 ( 09202-00010 )
4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
  
  Note
  
  Be careful not to damage the retainer.
INSTALL EXHAUST VALVE
1. Text in Illustration
  
  *a 30 mm (1.18 in.) or more
  
  Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.
2. Install the exhaust valve, compression spring and valve spring retainer to the cylinder head.
  
  Note
  
  Install the same parts in the same combination to their original locations.
3. Using SST and wooden blocks, compress the spring and install the valve spring retainer locks.
  
  SST
  
  09202-70020 ( 09202-00010 )
4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.
  
  Note
  
  Be careful not to damage the retainer.

Text in Illustration
*a	CORRECT
*b	INCORRECT