HYBRID CONTROL SYSTEM, Diagnostic DTC:P3107-213

DTC Code DTC Name
P3107-213 Lost Communication with Airbag System Control Module

DESCRIPTION


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 213

Short to ground in the communication circuit:

Communication from the airbag ECU assembly stopped and Circuit Low has been detected for a certain period.

(1 trip detection logic)

  • Wire harness or connector

  • Airbag sensor assembly

  • Power management control ECU
Related Data List
DTC No. Data List
P3107-213 Collision Signal (Airbag)

WIRING DIAGRAM

Refer to the wiring diagram for DTC P3107-214 Click here.

INSPECTION PROCEDURE

Tech Tips

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.


  1. Turn the power switch on (IG) and wait for 15 seconds or more.

PROCEDURE


  1. CHECK DTC OUTPUT (SRS AIRBAG)


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      Airbag system DTCs are not output. A
      Airbag system DTCs are output. B

    5. Turn the power switch off.


    B

    GO TO DTC CHART (AIRBAG SYSTEM) Click here

    A

  2. CHECK AIRBAG SENSOR ASSEMBLY (CHECK WAVEFORM)


    1. Connect an oscilloscope between the airbag sensor assembly terminals specified in the table below.

    2. Turn the power switch on (READY).

    3. Measure the waveform.

      A01I3U5E01
      Item Contents
      Terminal I47-14 (GSW2) - I47-25 (E1)
      Equipment Setting 5V/DIV., 500ms/DIV.
      Condition Power switch on (READY)
      Result
      Result Proceed to
      The waveform appears as shown in the illustration. A
      The waveform differs from the one shown in the illustration. B
      Text in Illustration
      *a

      Component with harness connected

      (Airbag Sensor Assembly)

    4. Turn the power switch off.


    B

    CHECK AIRBAG SENSOR ASSEMBLY Click here

    A

  3. CLEAR DTC


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Clear DTCs and freeze frame data.

    5. Turn the power switch off.


    NEXT

  4. CHECK DTC OUTPUT (HYBRID CONTROL)


    1. Connect the Techstream to the DLC3.

    2. Turn the power switch on (IG).

    3. Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P3107-213 is not output. A
      P3107-213 is output. B

    5. Turn the power switch off.


    B

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

    A

  5. CHECK FOR INTERMITTENT PROBLEMS

    Click here


    NG

    REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here

  6. CHECK AIRBAG SENSOR ASSEMBLY


    1. Disconnect the I47 airbag sensor assembly connector.

    2. A01I4S7E01
      Text in Illustration
      *a

      Component without harness connected

      (Airbag Sensor Assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      I47-14 (GSW2) - I47-25 (E1) Power switch off 10 kΩ or higher

    3. Reconnect the I47 airbag sensor assembly connector.


    NG

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - AIRBAG SENSOR ASSEMBLY)


    1. Disconnect the I4 power management control ECU connector.

    2. A01I4S7E02
      Text in Illustration
      *a

      Component without harness connected

      (Airbag Sensor Assembly)

      Disconnect the I47 airbag sensor assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      A01I3CAE02
      Text in Illustration
      *a

      Rear view of wire harness connector

      (to Power Management Control ECU)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)
      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      I4-13 (ABFS) or I47-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher

    4. Reconnect the I47 airbag sensor assembly connector.

    5. Reconnect the I3 power management control ECU connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE POWER MANAGEMENT CONTROL ECU Click here