REAR DOOR BELT MOULDING INSTALLATION

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. INSTALL REAR DOOR BELT MOULDING ASSEMBLY


    1. A01HZK0

      Engage the 6 claws to install the rear door belt moulding assembly as shown in the illustration.

  2. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A01HXO9

      Slide the rear door glass sub-assembly to install it as shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  3. INSTALL REAR DOOR QUARTER WINDOW GLASS


    1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.

    2. A01HZ3R

      Install the rear door quarter window glass together with the rear door quarter window weatherstrip as shown in the illustration.

  4. INSTALL REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01I169

      Install the rear door lower window frame sub-assembly with the screw and 2 bolts.

  5. INSTALL REAR DOOR GLASS RUN


    1. A01HYSQ

      Install the rear door glass run.

  6. INSTALL REAR DOOR WEATHERSTRIP


    1. A01I1OC

      Engage the 20 clips to install the rear door weatherstrip.

  7. INSTALL REAR DOOR CHECK ASSEMBLY


    1. Apply MP grease to the sliding parts of the rear door check assembly.

    2. Clean the bolt hole on the vehicle body.

    3. Clean the bolt threads of the bolt.

    4. Apply adhesive to the threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    5. A01HZZ0

      Install the rear door check assembly with the 2 nuts and bolt.

      Torque:
      Bolt
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }
      Nut
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

  8. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. A01HXFIE01
      Text in Illustration
      *a Reference Point

      Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. Install the new rear door service hole cover according to the reference points on the rear door panel.

      Note

      Securely install the rear door service hole cover preventing wrinkles and air bubbles.

    4. Connect the connector.

  9. INSTALL REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01HXJV

      Install the rear door inner glass weatherstrip.

  10. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HXLU

      Install the No. 1 door scuff plate clamp as shown in the illustration.

    2. A01HYE0E01
      Text in Illustration
      *1 Rear Door Inside Locking Cable Assembly
      *2 Rear Door Lock Remote Control Cable Assembly

      Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    3. A01I1VME01
      Text in Illustration
      *a Reference Boss

      Engage the 4 claws and reference boss as shown in the illustration.

    4. A01I0EO

      Engage the 8 clips to install the rear door trim board sub-assembly.

    5. Install the 3 screws.

    6. Remove protective tape.

  11. INSTALL REAR ARMREST ASSEMBLY


    1. A01I1M6

      Engage the 2 guides, 3 clips and 7 claws to install the rear armrest assembly.

  12. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. Connect the connector.

    2. A01I060

      Engage the 3 guides, 2 clips and 5 claws to install the rear power window regulator switch assembly with rear door armrest base panel.

  13. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01I1NP

      Engage the 3 claws to install the rear door inside handle bezel plug.

  14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  15. INSPECT POWER WINDOW OPERATION

    Click here