FRONT BUMPER REASSEMBLY


  1. INSTALL FRONT BUMPER SIDE RETAINER LH


    1. A01I001

      Engage the claw.

    2. Install the front bumper side retainer LH with the bolt.

  2. INSTALL FRONT BUMPER SIDE RETAINER RH

    Tech Tips

    Use the same procedure as for the LH side.

  3. INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY


    1. A01I0R7

      Install the front bumper reinforcement sub-assembly with the 6 bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    2. A01I0UM

      Engage each clamp.

  4. INSTALL NO. 2 FRONT BUMPER SUPPORT SPACER SUB-ASSEMBLY


    1. A01I1BY

      Engage the guide.

    2. A01HYZ5

      Install the No. 2 front bumper support spacer sub-assembly with the 4 bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    3. A01HYRX

      Engage the clamp.

  5. INSTALL FRONT BUMPER ENERGY ABSORBER


    1. A01HXRS

      Engage the 2 guides to install the front bumper energy absorber.

  6. INSTALL RADIATOR GRILLE EMBLEM ASSEMBLY


    1. A01HZQW

      Engage the 2 pins and 4 claws.

    2. A01HY2E

      Install the radiator grille emblem assembly to the radiator grille with the 2 screws.

  7. INSTALL RADIATOR GRILLE SUB-ASSEMBLY


    1. A01HZ9O

      Engage the 6 claws.

    2. A01I15Q

      Install the radiator grille sub-assembly with the 2 screws.

  8. INSTALL NO. 1 LOWER RADIATOR GRILLE


    1. Engage the 18 claws.

      A01I0PM
    2. A01HZKD

      Install the No. 1 lower radiator grille with the 6 screws.

  9. INSTALL FRONT FENDER LINER RETAINER


    1. A01I0BC

      Engage the claw to install the front fender liner retainer.

      Tech Tips

      Use the same procedure for the RH side and LH side.

  10. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/o Side Turn Signal Light)


    1. A01HZ1H

      Install the front bumper extension mounting bracket with the 4 screws.

  11. INSTALL FRONT BUMPER EXTENSION MOUNTING BRACKET (w/ Side Turn Signal Light)


    1. A01HYJ1

      Install the front bumper extension mounting bracket with the 4 screws.

  12. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY LH


    1. Install the front turn signal light assembly with the 2 screws.

  13. INSTALL FRONT TURN SIGNAL LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure as for the LH side.

  14. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure for all No. 1 ultrasonic sensor retainers.


    1. A01HYCYE01
      Text in Illustration
      *a Cutout
      *b Protrusion

      Engage the 2 claws to install the No. 1 ultrasonic sensor retainer to the front bumper assembly.

      Note


      • Do not damage the front bumper assembly with the protrusion when installing the No. 1 ultrasonic sensor retainer.

      • Securely install the No. 1 ultrasonic sensor retainer so that there are no gaps between the No. 1 ultrasonic sensor retainer and surface of the front bumper assembly.

      Tech Tips

      When installing the No. 1 ultrasonic sensor retainer, align the cutout and protrusion as shown in the illustration.

  15. INSTALL NO. 1 ULTRASONIC SENSOR (w/ Intuitive Parking Assist System)

    Tech Tips

    Use the same procedure for all No. 1 ultrasonic sensors.


    1. Engage the 2 claws to install the No. 1 ultrasonic sensor to the No. 1 ultrasonic sensor retainer.

      Note

      Push the No. 1 ultrasonic sensor retainer from the outside of the front bumper assembly when there is a gap between the No. 1 ultrasonic sensor retainer and the front bumper assembly surface. In this case, do not push on the No. 1 ultrasonic sensor.