FRONT WIPER MOTOR INSTALLATION


  1. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY


    1. Using a T30 "TORX" socket wrench, install the windshield wiper motor assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    2. Connect the connector.

    3. Turn the ignition switch to ON (IG).

    4. Operate the wiper and stop the windshield wiper motor assembly at the automatic stop position.

    5. Turn the ignition switch off.

    6. Disconnect the connector.

    7. A01I1TDE01
      Text in Illustration
      *a Pivot of the windshield wiper motor assembly

      Apply MP grease to the pivot of the windshield wiper motor assembly.

    8. A01I1WRE01
      Text in Illustration
      *1 No. 1 Rod
      *a Pivot of the windshield wiper motor assembly

      Connect the No. 1 rod to the pivot of the windshield wiper motor assembly.

  2. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY


    1. A01HZGCE01
      Text in Illustration
      *1 Motor Grommet

      Engage the motor grommet as shown in the illustration.

      Note

      Be careful not to damage the windshield when installing the windshield wiper motor and link assembly.

    2. Install the windshield wiper motor and link assembly with the 2 bolts.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }

    3. Connect the connector.

  3. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    1. Engage the 8 guides as shown in the illustration.

      A01HZYB

    2. Engage the 6 claws and guide to install the cowl top ventilator louver sub-assembly.

      A01I0PS

  4. INSTALL FRONT FENDER TO COWL SIDE SEAL LH


    1. A01I0CK

      Engage the 3 guides and 2 clips to install the front fender to cowl side seal LH as shown in the illustration.

  5. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

    Tech Tips

    Use the same procedure as for the LH side.

  6. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    1. A01I1IRE01
      Text in Illustration
      *a Wiper Arm Serration

      When reusing the front wiper arm and blade assembly LH:


      1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

        Note

        Do not grind down the wiper arm serrations.

    2. A01HZGOE01
      Text in Illustration
      *a Wiper Pivot Serration

      When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    3. A01HZFSE01
      Text in Illustration
      *1 Ceramic Dot

      Set the front wiper arm and blade assembly LH in the range shown in the illustration and then install the front wiper arm and blade assembly LH with the nut.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }
      Area Measurement
      A 7.5 mm (0.295 in.)

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

  7. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    1. A01I1IRE01
      Text in Illustration
      *a Wiper Arm Serration

      When reusing the front wiper arm and blade assembly RH:


      1. Clean the wiper arm serrations to remove any burrs, dirt, etc.

        Note

        Do not grind down the wiper arm serrations.

    2. A01HZGOE01
      Text in Illustration
      *a Wiper Pivot Serration

      When reusing the windshield wiper link assembly:


      1. Clean the wiper pivot serrations with a wire brush.

    3. A01I1U0E01
      Text in Illustration
      *1 Ceramic Dot

      Set the front wiper arm and blade assembly RH in the range shown in the illustration and then install the front wiper arm and blade assembly RH with the nut.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }
      Area Measurement
      A 7.5 mm (0.295 in.)

      Tech Tips

      Hold the wiper arm by hand while tightening the nut.

    4. Turn the ignition switch to ON (IG).

    5. Operate the front wiper while spraying washer fluid onto the windshield glass. Make sure that the front wiper functions properly and the wiper does not come into contact with the vehicle body.

    6. Lift each wiper arm twice after the wipers stop and check the wiper set position.

    7. Turn the ignition switch off.