OUTER MIRROR SWITCH INSPECTION


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY


    1. w/o Retract mirror


      1. Check the mirror select switch and mirror surface adjust switch.

      2. A01HXPGE01
        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        15 (VL) - 19 (B)

        17 (M+) - 18 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        15 (VL) - 18 (E)

        17 (M+) - 19 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        16 (HL) - 19 (B)

        17 (M+) - 18 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        16 (HL) - 18 (E)

        17 (M+) - 19 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        14 (VR) - 19 (B)

        17 (M+) - 18 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        14 (VR) - 18 (E)

        17 (M+) - 19 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        13 (HR) - 19 (B)

        17 (M+) - 18 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        13 (HR) - 18 (E)

        17 (M+) - 19 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Check the LED illuminates (w/o Retract mirror).


      1. A01HXPGE02
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 12 (ILL+)

        Battery negative (-) → Terminal 22 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.

    3. w/ Retract mirror


      1. Check the mirror select switch and mirror surface adjust switch.

      2. A01I1LFE01
        Text in Illustration
        *1 Mirror select switch
        *2 Mirror surface adjust switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Turn the mirror select switch to the L position.

      3. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for left side)
        Tester Connection Switch Condition Specified Condition

        15 (VL) - 19 (B)

        17 (M+) - 18 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        15 (VL) - 18 (E)

        17 (M+) - 19 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        16 (HL) - 19 (B)

        17 (M+) - 18 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        16 (HL) - 18 (E)

        17 (M+) - 19 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

      4. Turn the mirror select switch to the R position.

      5. Measure the resistance according to the value(s) in the table below.

        Standard Resistance (for right side)
        Tester Connection Switch Condition Specified Condition

        14 (VR) - 19 (B)

        17 (M+) - 18 (E)

        		 UP Below 1 Ω
        OFF 10 kΩ or higher

        14 (VR) - 18 (E)

        17 (M+) - 19 (B)

        		 DOWN Below 1 Ω
        OFF 10 kΩ or higher

        13 (HR) - 19 (B)

        17 (M+) - 18 (E)

        		 LEFT Below 1 Ω
        OFF 10 kΩ or higher

        13 (HR) - 18 (E)

        17 (M+) - 19 (B)

        		 RIGHT Below 1 Ω
        OFF 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    4. Check the mirror retract switch.


      1. A01I1LFE02
        Text in Illustration
        *1 Mirror retract switch
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        21 (MF) - 18 (E) Mirror retract switch retract position Below 1 Ω
        20 (MR) - 19 (B) Below 1 Ω
        21 (MF) - 19 (B) Mirror retract switch return position Below 1 Ω
        20 (MR) - 18 (E) Below 1 Ω

        If the result is not as specified, replace the outer mirror switch assembly.

    5. Check the LED illuminates (w/ Retract mirror).


      1. A01I1LFE03
        Text in Illustration
        *a

        Component without harness connected

        (Outer Mirror Switch Assembly)

        Apply battery voltage to the outer mirror switch assembly and check that the LED illuminates.

        Standard
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 12 (ILL+)

        Battery negative (-) → Terminal 22 (ILL-)

        		 LED illuminates

        If the result is not as specified, replace the outer mirror switch assembly.