LUGGAGE DOOR LOCK CONTROL CABLE ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Manual Seat)

    Click here

  4. REMOVE FRONT SEAT ASSEMBLY LH (for TMMK Made Power Seat)

    Click here

  5. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Manual Seat)

    Click here

  6. REMOVE FRONT SEAT ASSEMBLY LH (for SIA Made Power Seat)

    Click here

  7. REMOVE REAR SEAT CUSHION ASSEMBLY


    1. Disengage the hook of the seat cushion from the vehicle body as shown in the illustration.

      Note

      Follow the instructions below carefully as the cushion frame can be deformed easily.


      1. A01I27UE01

        Choose a hook to disengage first. Place your hands near the hook as shown in the illustration. Then lift the seat cushion to disengage the hook.

        Standard Measurement
        a 100 mm (3.94 in.) or less

      2. Repeat the step above for the other hook.

    2. Remove the rear seat cushion assembly.

  8. REMOVE REAR SEAT CUSHION LOCK HOOK


    1. A01HXMA

      Disengage the claw and remove the rear seat cushion lock hook.

      Note

      Rear seat cushion lock hooks must not be reused.

      Tech Tips

      Use the same procedure for the RH side and the LH side.

  9. REMOVE REAR SIDE SEATBACK ASSEMBLY LH


    1. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

    2. Disconnect the connector.

    3. A01HZMU

      Remove the 2 bolts.

    4. Disengage the hook and remove the rear side seatback assembly LH.

  10. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I27F

      Disengage the 10 claws and remove the front door scuff plate LH.

  11. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the front door opening trim weatherstrip.

  12. REMOVE REAR DOOR SCUFF PLATE LH


    1. A01I1O6

      Disengage the 6 claws and remove the rear door scuff plate LH.

      Tech Tips

      Disengage the claws from the rear side of the scuff plate.

  13. DISCONNECT REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Disconnect the rear door opening trim weatherstrip.

  14. REMOVE LAP BELT OUTER ANCHOR COVER


    1. A01HZVD

      Disengage the 3 claws and remove the lap belt outer anchor cover.

  15. DISCONNECT FRONT SEAT OUTER BELT ASSEMBLY LH


    1. A01HZ2T

      Remove the bolt and disconnect the floor anchor of the front seat outer belt assembly.

  16. REMOVE CENTER PILLAR LOWER GARNISH LH


    1. A01HY8V

      Disengage the 2 claws and 3 clips, and remove the center pillar lower garnish LH.

  17. REMOVE LUGGAGE COMPARTMENT DOOR COVER


    1. A01HYJE

      Remove the 13 clips and luggage compartment door cover.

  18. REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH


    1. A01I0N8

      Remove the 2 clips.

    2. Disengage the clip and remove the luggage compartment door hinge cover LH.

  19. REMOVE SPARE WHEEL COVER ASSEMBLY


    1. Remove the spare wheel cover assembly.

  20. REMOVE REAR FLOOR FINISH PLATE


    1. A01I1K5

      Remove the 5 clips.

    2. A01HZHR

      Disengage the 4 clips and remove the rear floor finish plate.

  21. REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK


    1. A01I1Y1E01
      Text in Illustration
      *a Pin

      Push in the pin and remove the No. 1 luggage compartment trim hook.

  22. REMOVE LUGGAGE COMPARTMENT INNER TRIM COVER LH


    1. A01I043

      Remove the 2 clips.

    2. Disengage the fastener and remove the luggage compartment inner trim cover LH.

  23. REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY


    1. A01HZWD

      Remove the screw.

    2. A01HYWI

      Disengage the guide and disconnect the fuel lid lock open lever sub-assembly as shown in the illustration.

    3. A01HZLL

      Disconnect the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly and remove the fuel lid lock open lever sub-assembly.

  24. REMOVE LUGGAGE DOOR LOCK CONTROL CABLE SUB-ASSEMBLY


    1. A01HZEP

      Disengage the 2 clamps.

    2. A01HZPS

      Using a clip remover, disengage the clamp and disconnect the wire harness.

    3. A01HYQH

      Using a clip remover, disengage the 2 clamps and remove the 2 scuff plate clips.

    4. Turn back the floor carpet so that the luggage door lock control cable sub-assembly and fuel lid lock control cable sub-assembly can be removed.

    5. A01I08Y

      Disengage the guide as shown in the illustration.

    6. A01I0CF

      Disconnect the luggage door lock control cable sub-assembly.

    7. A01HYXD

      Disengage the clamp and disconnect the luggage door lock control cable sub-assembly.

    8. A01HYXFE02
      Text in Illustration
      *a Cutout
      *b Guide (A)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and the guides (A), and then pull the fuel filler opening lid lock retainer.

    9. A01I0TVE02
      Text in Illustration
      *a Cutout
      *b Guide (B)

      Rotate the fuel filler opening lid lock retainer as shown in the illustration to align the cutouts and guides (B), and then pull the fuel filler opening lid lock retainer.

    10. A01I1T7E02
      Text in Illustration
      *a Cutout
      *b Guide (C)
      *c Guide (B)

      Pull out the fuel filler opening lid lock retainer with both guides (B) and (C) aligned with the cutouts.

    11. A01HZ1J

      Disengage the 2 claws and remove the fuel filler opening lid lock retainer.

    12. Disengage the 10 clamps and remove the fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

      A01I1PFE01
      Text in Illustration
      *1 Fuel Lid Lock Control Cable Sub-assembly *2 Luggage Door Lock Control Cable Sub-assembly

    13. Using a knife, cut off the clamp as shown in the illustration.

      A01HXNJE02
      Text in Illustration
      *a Tape *b Cut

      Note

      Be careful not to damage the vehicle fuel lid lock control cable sub-assembly and luggage door lock control cable sub-assembly.

    14. Remove the clamp.

    15. Remove the 3 pieces of tape and fuel lid lock control cable sub-assembly.