POWER WINDOW REGULATOR MOTOR (for Front Door) REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HZJZ

      Using a moulding remover, disengage the 3 claws and remove the front door inside handle bezel plug as shown in the illustration.

  4. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)


    1. A01I1UQ

      Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator master switch assembly with front door armrest base panel.

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)


    1. A01I1WB

      Using a moulding remover, disengage the 2 clips, 6 claws and 3 guides as shown in the illustration.

    2. Disconnect each connector and remove the power window regulator switch assembly with front door armrest base panel.

  6. REMOVE FRONT ARMREST ASSEMBLY


    1. A01HYAS

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the front armrest assembly.

  7. REMOVE COURTESY LIGHT ASSEMBLY


    1. A01HXETE01
      Text in Illustration
      *A for LH Side
      *B for RH Side
      *1 Protective Tape

      Using a screwdriver with its tip wrapped with protective tape, disengage the claw.

    2. Disconnect the connector and remove the courtesy light assembly.

  8. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01I206E01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the front door panel.

    2. A01I1QO

      Remove the 3 screws.

    3. Using a clip remover, disengage the 10 clips.

    4. A01HYWEE01
      Text in Illustration
      *1 Front Door Inner Glass Weatherstrip
      *a Reference Boss

      Pull out the front door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the front door panel.

    6. Raise the front door trim board sub-assembly to remove the front door trim board sub-assembly together with the front door inner glass weatherstrip.

    7. A01HY4G

      Disengage the clamp.

    8. Disconnect the front door lock remote control cable assembly and front door inside locking cable assembly.

  9. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP


    1. A01HXMTE01
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the 4 claws and remove the front door inner glass weatherstrip from the front door trim board sub-assembly as shown in the illustration.

  10. REMOVE DOOR SIDE AIRBAG SENSOR


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Disconnect the connector from the door side airbag sensor.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

        A01HXLQE12
        Text in Illustration
        *1 White Housing Lock *2 Yellow CPA
        *a Connector Lock is Released - -

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting.

    4. A01HYOT

      Remove the bolt and door side airbag sensor from the front door panel.

      Note

      Loosen the bolt while holding the door side airbag sensor because the door side airbag sensor pin (stopper) is easily damaged.

    5. After disconnecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

      A01HY50E01
      Text in Illustration
      *a Incorrect *b Correct

  11. REMOVE FRONT DOOR SERVICE HOLE COVER


    1. A01I0T5

      Remove the bolt.

    2. Disconnect each connector.

    3. Disengage the 5 clamps.

    4. Pass the front door lock remote control cable assembly, front door inside locking cable assembly and each connector through the front door service hole cover.

    5. Remove the front door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the front door panel.

  12. REMOVE NO. 1 FRONT DOOR SERVICE HOLE SEAL


    1. A01HYIH

      Remove the No. 1 front door service hole seal.

  13. REMOVE NO. 2 FRONT DOOR SERVICE HOLE SEAL


    1. A01I216

      Remove the No. 2 front door service hole seal.

  14. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY


    1. A01I1K2

      Remove the grommet.

    2. Connect the cable to the negative (-) battery terminal.

    3. for Driver Side:


      1. Connect the power window regulator master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator master switch assembly.

    4. for Front Passenger Side:


      1. Connect the power window regulator switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.

      2. Disconnect the power window regulator switch assembly.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    6. A01I0GP

      Remove the 2 bolts.

      Note

      After the bolts are removed, do not allow the front door glass sub-assembly to fall.

    7. A01I0ZEE02

      Remove the front door glass sub-assembly as indicated by the arrows, in the order shown in the illustration.

      Note

      Do not damage the front door glass sub-assembly.

  15. REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY


    1. A01I0VJE03
      Text in Illustration
      *a Temporary Bolt

      Loosen the temporary bolt.

      Note

      Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator assembly may fall and cause damage.

    2. Remove the 5 bolts.

    3. Remove the front door window regulator assembly.

    4. Remove the temporary bolt from the front door window regulator assembly.

  16. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY


    1. A01HZX0

      Using a T25 "TORX" socket wrench, remove the 3 screws and front power window regulator motor assembly.