CENTER AIRBAG SENSOR ASSEMBLY REMOVAL


  1. REMOVE LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

    Click here

  2. REMOVE REAR CONSOLE BOX ASSEMBLY

    Click here

  3. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I27F

      Disengage the 10 claws and remove the front door scuff plate LH.

  4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01I1YY

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  5. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

    Tech Tips

    Disconnect the front door opening trim weatherstrip LH to the extent that allows the removal of the instrument side panel LH.

  6. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01I23L

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HZF4

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  7. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01I14J

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  8. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01I26P

      Remove the bolt <B> and screw <C> or <D>.

    2. A01HZC8

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  9. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY


    1. A01HZXS

      Remove the 2 screws <C> or <D>.

    2. Open the lower instrument panel door.

    3. A01HYSX

      Remove the 3 screws <C> or <D>.

    4. A01I0YB

      Disengage the 2 clips and guide as shown in the illustration.

    5. A01I288

      Disengage the clamp.

    6. Disengage the glove compartment light as shown in the illustration.

    7. Disconnect the connector and remove the lower instrument panel sub-assembly.

  10. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. A01HZFH

      Remove the 2 screws <C> or <D>.

    2. A01I0CZ

      Disengage the 2 clips and guide as shown in the illustration.

    3. Disconnect each connector to remove the upper console panel sub-assembly.

  11. REMOVE FRONT NO. 2 CONSOLE BOX INSERT


    1. A01HZOJ

      Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.

    2. A01HXVN

      Remove the screw <C> or <D>.

    3. A01I0C3

      Disengage the 2 clips and guide to remove the front No. 2 console box insert as shown in the illustration.

  12. REMOVE CONSOLE BOX INSERT


    1. A01I1BO

      Remove the screw <C> or <D>.

    2. A01I1R5

      Disengage the 2 clips and guide to remove the console box insert as shown in the illustration.

  13. REMOVE FLOOR CARPET BRACKET LH


    1. A01I0KA

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket LH.

  14. REMOVE FLOOR CARPET BRACKET RH


    1. A01HZ44

      Remove the 2 clips.

    2. Disengage the 2 guides to remove the floor carpet bracket RH.

  15. REMOVE NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct)


    1. A01HZX8

      Remove the clip and No. 1 console box duct.

  16. REMOVE AIRBAG SENSOR ASSEMBLY


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Turn back the carpet.

    4. A01I1ZI

      Disconnect the connectors from the airbag sensor assembly as shown in the illustration.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.

    5. Remove the 3 bolts and airbag sensor assembly.