REAR SEAT SIDE AIRBAG ASSEMBLY DISPOSAL

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


  1. PRECAUTION

    CAUTION:


    • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

    • Never dispose of a rear seat airbag assembly with an undeployed airbag.

    • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

    • When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.

    • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the rear seat airbag assembly.

    • The rear seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

    • Use gloves and safety glasses when handling a rear seat airbag assembly with a deployed airbag.

    • Do not apply water etc. to a rear seat airbag assembly with a deployed airbag.

    • Always wash your hands with water after completing the operation.

    Tech Tips

    When scrapping a vehicle equipped with an SRS or disposing of the rear seat airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of TOYOTA MOTOR SALES, U.S.A., INC.

  2. DISPOSE OF REAR SEAT AIRBAG ASSEMBLY (When Installed in Vehicle)

    Note


    • When disposing of the rear seat airbag assembly, never use the customer's vehicle to deploy the airbag.

    • Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01I00LE06

      Check the function of SST Click here.

      SST
      09082-00700
    2. Refer to Precaution Click here.

    3. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    4. Remove the rear seat cushion assembly Click here.

    5. Disconnect the connector from the rear seat airbag assembly.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. A01HYBSE03
        Text in Illustration
        *1 White Housing Lock
        *2 Yellow CPA
        *a Slide

        Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

      2. Push down the white housing lock again and disconnect the connector.

        Note

        Do not push down the part (A) shown in the illustration when disconnecting.

    6. Install SST.

      CAUTION:

      Check that there is no looseness in the rear side seatback assembly.


      1. A01HZ0UE01

        Connect the SST connector to the rear seat airbag assembly connector.

        SST
        09082-00700
        09082-00820

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock.

      2. A01I20HE03
        Text in Illustration
        *1 Battery
        *a 10 m (32.8 ft.) or more

        Move SST at least 10 m (32.8 ft.) away from the rear side window.

      3. Maintaining sufficient clearance for the SST wire harness in the rear side window, close all doors and windows of the vehicle.

        Note

        Take care not to damage the SST wire harness.

      4. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

    7. Deploy the airbag.


      1. Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

      2. Press the SST activation switch and deploy the airbag.

        CAUTION:


        • Before deployment, make sure that no one is near the vehicle.

        • The rear seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

        • Use gloves and safety glasses when handling a rear seat airbag assembly with a deployed airbag.

        • Do not apply water etc. to a rear seat airbag assembly with a deployed airbag.

        • Always wash your hands with water after completing the operation.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

  3. DISPOSE OF REAR SEAT AIRBAG ASSEMBLY (When Not Installed in Vehicle)

    Note

    Be sure to observe the following procedure when deploying the airbag.

    Tech Tips

    Prepare a battery as the power source to deploy the airbag.


    1. A01I00LE06

      Check the function of SST Click here.

      SST
      09082-00700
    2. Remove the rear seat airbag assembly Click here.

      CAUTION:


      • Before removing the rear side seatback assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

      • When storing the rear seat airbag assembly, keep the airbag deployment side facing upward.

    3. A01HYEBE42

      Using braided wire, tie down the rear seat airbag assembly to an unneeded tire.

      Text in Illustration
      *1 Stripped Wire Section
      *a Wire Diameter
      Wire
      Stripped wire section
      1.25 mm2 (0.0019 in.2) or more

      CAUTION:

      If the wire is too thin or an alternative object is used to tie down the rear seat airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2(0.0019 in.2).

      Tech Tips

      To calculate the area of the stripped wire section:

      Area = 3.14 x (Diameter)2/ 4


      1. A01I25G

        Install the 2 nuts to the rear seat airbag assembly.

      2. A01HYDF

        Wind the wires around the stud bolts of the rear seat airbag assembly as shown in the illustration.

      3. A01I1VTE01
        Text in Illustration
        *a Width
        *b Inner Diameter

        Position the rear seat airbag assembly inside the tire.

        Minimum tire size
        Width
        185 mm (7.28 in.)
        Inner diameter
        360 mm (1.18 ft.)

        CAUTION:


        • Make sure that the wires are tight. If there is slack in the wires, the rear seat airbag assembly may break loose when the airbag is deployed.

        • Face the rear seat airbag assembly deployment surface toward the inside the tire to evenly distribute the force of deployment.

        Note

        The tire may be marked by the airbag deployment, so use an unneeded tire.

    4. Install SST.


      1. A01I15EE01

        Connect the SST connector to the rear seat airbag assembly connector.

        SST
        09082-00820
    5. Place the tires.


      1. A01I08OE01
        Text in Illustration
        *1 Tires (2 or more)

        Place at least 2 tires under the tire to which the rear seat airbag assembly is tied.

        Note

        Do not place the SST connector under the tire because it could be damaged.

      2. Place at least 2 tires onto the tire to which the rear seat airbag assembly is tied. The top tire should have a wheel installed.

      3. A01HY39

        Tie the tires together with the 2 wires.

        CAUTION:

        Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.

    6. Install SST.


      1. A01I18KE01
        Text in Illustration
        *1 Rear Seat Airbag Assembly
        *2 Battery
        *a 10 m (32.8 ft.) or more

        Connect the SST connector.

        SST
        09082-00700

        Note

        To avoid damaging the SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tire.

      2. Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tire.

    7. Deploy the airbag.


      1. Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

      2. Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the rear seat airbag assembly is tied.

      3. Press the SST activation switch and deploy the airbag.

        CAUTION:

        Before deployment, make sure that no one is near the airbag.

        Tech Tips

        The airbag is deployed as the LED of the SST activation switch comes on.

    8. Dispose of the rear seat airbag assembly.

      CAUTION:


      • The rear seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

      • Use gloves and safety glasses when handling a rear seat airbag assembly with a deployed airbag.

      • Do not apply water etc. to a rear seat airbag assembly with a deployed airbag.

      • Always wash your hands with water after completing the operation.


      1. Remove the rear seat airbag assembly from the tire.

      2. Place the rear seat airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.