AIRBAG SYSTEM SRS Warning Light does not Come ON

DESCRIPTION

The SRS warning light is located on the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to ON, and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not stored in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

A01HZ9RE01

INSPECTION PROCEDURE

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK BATTERY VOLTAGE


    1. Measure the voltage of the battery.

      Standard Voltage
      11 to 14 V
      Result
      Result Proceed to
      OK A
      NG (for 2AR-FE) B
      NG (for 2GR-FE) C

    B

    INSPECT CHARGING SYSTEM AND BATTERY Click here

    C

    INSPECT CHARGING SYSTEM AND BATTERY Click here

    A

  2. CHECK CONNECTOR


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the connector is properly connected to the combination meter assembly.

      OK
      The connector is properly connected.

      Tech Tips

      If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

    4. Disconnect the connector from the combination meter assembly.

    5. Check that the terminal of the connector is not damaged.

      OK
      The terminal is not deformed or damaged.

    NG

    REPAIR OR REPLACE CONNECTOR

    OK

  3. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)


    1. A01HYHBE08
      Text in Illustration
      *A w/o Multi-information Display
      *B w/ Multi-information Display
      *a

      Front view of wire harness connector

      (to Combination Meter Assembly)

      Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      I18-13 (IG+) - Body ground Ignition switch ON 11 to 14 V
      I18-1 (B) - Body ground Always 11 to 14 V

    4. Turn the ignition switch off.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      w/o Multi-information Display:
      Tester Connection Condition Specified Condition
      I18-7 (ES) - Body ground Always Below 1 Ω
      w/ Multi-information Display:
      Tester Connection Condition Specified Condition
      I18-20 (ES) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE WIRE HARNESS

    OK

  4. CHECK SRS WARNING LIGHT


    1. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    2. Connect the connector to the combination meter assembly.

    3. Disconnect the connector from the airbag sensor assembly.

    4. Connect the cable to the negative (-) battery terminal.

    5. Turn the ignition switch to ON and check the SRS warning light condition.

      OK
      After the primary check period, the SRS warning light goes off for approximately 10 seconds and comes back on.

      Tech Tips

      The primary check period is approximately 6 seconds after the ignition switch is turned to ON.


    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE AIRBAG SENSOR ASSEMBLY Click here