METER / GAUGE SYSTEM ON-VEHICLE INSPECTION


  1. INSPECT COMBINATION METER ASSEMBLY


    1. INSPECT SPEEDOMETER

      Note


      • The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (skid control ECU) via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (skid control ECU) because it is the source of the vehicle speed signal.

      • Data List values of the brake actuator assembly (skid control ECU) are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.

      • If the tire size or tire inflation pressure is not within the specified range, or the tires are excessively worn, the speedometer indication error will increase. Therefore, make sure to perform this inspection after checking that the tire size, tire inflation pressure and tire wear are in the specified range.


      1. Before starting the following inspection, check if the vehicle stability control system outputs the DTCs.

      2. Read the Data List according to the display on the Techstream.

        ABS/VSC/TRAC
        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        Vehicle Speed Maximum wheel speed sensor reading/Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
        Standard: mph
        Techstream Indication (mph) Acceptable Range (mph)
        20 19.5 to 22.5
        40 39.5 to 43.0
        60 59.5 to 63.5
        80 79.5 to 84.0
        100 99.5 to 104.5
        120 119.5 to 125.0
        Standard: km/h (w/o Side Turn Signal Light)
        Techstream Indication (km/h) Acceptable Range (km/h)
        20 18.5 to 22.5
        40 39.0 to 43.0
        60 59.0 to 64.0
        80 79.0 to 85.0
        100 99.5 to 105.5
        120 120.0 to 126.0
        140 140.0 to 147.0
        160 160.0 to 168.0
        180 180.0 to 189.0
        200 200.0 to 210.0
        Standard: km/h (w/ Side Turn Signal Light)
        Techstream Indication (km/h) Acceptable Range (km/h)
        20 21.0 to 25.0
        40 41.7 to 46.2
        60 62.7 to 67.2
        80 83.4 to 88.4
        100 104.3 to 109.3
        120 125.1 to 130.6
        140 145.8 to 151.8
        160 166.2 to 173.2
        180 186.9 to 194.5
        200 207.7 to 215.7

    2. INSPECT TACHOMETER


      1. Connect the Techstream, and start the engine.

      2. Compare the test results with the tachometer indications.

        Standard
        Techstream Indication (rpm)

        Acceptable Range (rpm)

        Data in ( ) is for Reference
        700 630 to 770
        1000 (900 to 1100)
        2000 (1850 to 2150)
        3000 2800 to 3200
        4000 (3800 to 4200)
        5000 4800 to 5200
        6000 (5750 to 6250)
        7000 6700 to 7300

    3. CHECK LED ILLUMINATION


      1. Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.

        OK
        Warning or Indicator Light Specified Condition
        Washer fluid level warning light*2 Warning or indicator light comes on for about 3 seconds after turning the ignition switch to ON.
        Tire pressure warning light*4
        Master warning light*1
        Eco driving indicator light
        Brake warning light
        Slip indicator light
        ABS warning light
        VSC OFF indicator light
        TRAC OFF indicator light*2
        PCS OFF warning light*3
        SRS warning light Warning light comes on for about 6 seconds after turning the ignition switch to ON.
        Engine oil pressure warning light*2 Warning light comes on when turning the ignition switch to ON.
        Charge warning light*2
        EPS warning light
        MIL (Check engine warning light)

        • *1: w/ Multi-information Display

        • *2: w/o Multi-information Display

        • *3: w/ Pre-collision System

        • *4: w/ Tire Pressure Warning System