REMOTE ENGINE STARTER SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Tech Tips

    Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Connect the Techstream to the DLC3.

    2. Turn the engine switch on (IG).

    3. Enter the following menus: Body Electrical / Remote Engine Starter or Smart Key / Data List.

    4. Read the Data List according to the display on the Techstream.

      Remote Engine Starter (Remote Engine Starter ECU)
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Air Conditioner Mode Air conditioner linked with remote engine starter/Auto or User

      Auto: Air conditioner linked with remote engine starter mode "Auto"

      User: Air conditioner linked with remote engine starter mode "User"

      		 -
      Defogger Control Rear window defogger linked with remote engine starter/ON or OFF

      ON: Rear window defogger linked with remote engine starter enabled

      OFF: Rear window defogger linked with remote engine starter disabled

      		 -
      Trouble Factor Code 01 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 01 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 01 will be displayed -
      Trouble Factor Code 02 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 02 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 02 will be displayed -
      Trouble Factor Code 03 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 03 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 03 will be displayed -
      Trouble Factor Code 04 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 04 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 04 will be displayed -
      Trouble Factor Code 05 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 05 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 05 will be displayed -
      Trouble Factor Code 06 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 06 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 06 will be displayed -
      Trouble Factor Code 07 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 07 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 07 will be displayed -
      Trouble Factor Code 08 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 08 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 08 will be displayed -
      Trouble Factor Code 09 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 09 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 09 will be displayed -
      Trouble Factor Code 10 Number of engine stop factor/Min.: 0, MAX.: 255 Engine stop factor number will be displayed Refer to Diagnosis System
      Num of Trouble 10 Number of trouble factor code/Min.: 0, MAX.: 255 Number of trouble factor code 10 will be displayed -
      Ignition Switch Engine switch signal/ON or OFF

      ON: Engine switch on (IG)

      OFF: Engine switch off

      		 -
      Accessory Switch Engine switch signal/ON or OFF

      ON: Engine switch on (ACC)

      OFF: Engine switch off

      		 -
      Starter Switch Ignition switch signal/ON or OFF

      ON: Ignition switch ON

      OFF: Ignition switch off

      		 w/o Smart Key System
      Hood Courtesy Switch Engine hood courtesy switch signal/ON or OFF

      ON: Engine hood open

      OFF: Engine hood closed

      		 -
      Shift Position P Signal Shift P position signal/ON or OFF

      ON: Shift lever in P

      OFF: Shift lever not in P

      		 -
      Remote E/G starter ID Registry Remote engine starter ID/ON or OFF

      ON: Remote engine starter ID registered

      OFF: Remote engine starter ID not registered

      		 -
      Number of DTCs Number of diagnostic trouble code/Min.: 0, MAX.: 255 Number of DTCs will be displayed -
      Smart Key (Certification ECU (Smart Key ECU Assembly))
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      # Codes Number of diagnostic trouble code/Min.: 0, MAX.: 255 Number of DTCs will be displayed -
      Wireless Starter Com ID Certification between remote engine starter ECU and certification ECU (smart key ECU assembly)/No Regd or Regd

      No Regd: Certification between remote engine starter ECU and certification ECU (smart key ECU assembly) not complete

      Regd: Certification between remote engine starter ECU and certification ECU (smart key ECU assembly) complete

      		 -
      Wireless C Code Registration status between remote engine starter ECU and certification ECU (smart key ECU assembly)/No Regd or Regd

      No Regd: ID not registered between remote engine starter ECU and certification ECU (smart key ECU assembly)

      Regd: ID registered between remote engine starter ECU and certification ECU (smart key ECU assembly)

      Problems may be caused by the following:


      • DTC B2779 is stored.

      • Remote engine starter ECU registration has not been performed.

      • Malfunctions in the certification ECU (smart key ECU assembly) or remote engine starter ECU.