REAR DOOR LOCK REMOVAL

Tech Tips


  • Use the same procedure for the LH side and RH side.

  • The following procedure is for the LH side.


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG


    1. A01HXPB

      Using a moulding remover, disengage the 3 claws and remove the rear door inside handle bezel plug as shown in the illustration.

  4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL


    1. A01HZD8

      Using a moulding remover, disengage the 2 clips, 5 claws and 3 guides as shown in the illustration.

    2. Disconnect the connector and remove the rear power window regulator switch assembly with rear door armrest base panel.

  5. REMOVE REAR ARMREST ASSEMBLY


    1. A01HYVF

      Using a moulding remover, disengage the 3 clips, 7 claws and 2 guides and remove the rear armrest assembly.

  6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A01HZ67E01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the rear door panel.

    2. A01I0EO

      Remove the 3 screws.

    3. Using a clip remover, disengage the 8 clips.

    4. A01I07HE01
      Text in Illustration
      *1 Rear Door Inner Glass Weatherstrip
      *a Reference Boss

      Pull out the rear door trim board sub-assembly in the direction indicated by the arrow as shown in the illustration.

    5. Disengage the reference boss from the rear door panel.

    6. Raise the rear door trim board sub-assembly to remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.

    7. A01I06T

      Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly.

    8. A01HXYAE02
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the claw and remove the No. 1 door scuff plate clamp from the rear door trim board sub-assembly as shown in the illustration.

  7. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP


    1. A01HY2SE02
      Text in Illustration
      *a Screwdriver

      Using a screwdriver, disengage the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.

  8. REMOVE REAR DOOR SERVICE HOLE COVER


    1. A01HZPP

      Disconnect the connector.

    2. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through the rear door service hole cover.

    3. Remove the rear door service hole cover.

      Tech Tips

      Remove any remaining butyl tape from the rear door panel.

  9. DISCONNECT REAR DOOR WEATHERSTRIP


    1. A01I1XI

      Disconnect the upper part of rear door weatherstrip as shown in the illustration.

  10. REMOVE REAR DOOR GLASS RUN


    1. A01HYSQ

      Remove the rear door glass run.

  11. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY


    1. A01I169

      Remove the 2 bolts and screw, and rear door lower window frame sub-assembly.

      Note

      When the rear door lower window frame sub-assembly is removed, do not allow the rear door quarter window glass to fall.

  12. REMOVE REAR DOOR QUARTER WINDOW GLASS


    1. A01HXYW

      Remove the rear door quarter window glass with the rear door quarter window weatherstrip as shown in the illustration.

    2. Remove the rear door quarter window glass from the rear door quarter window weatherstrip.

  13. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


    1. A01HYZW

      Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

  14. REMOVE REAR DOOR LOCK WITH MOTOR ASSEMBLY


    1. A01HXFWE01
      Text in Illustration
      *1 Release Plate

      Using a T30 "TORX" socket wrench, remove the 3 screws.

    2. Move the rear door lock with motor assembly downward to disconnect it from the release plate of the rear door outside handle frame sub-assembly and remove the rear door lock with motor assembly.

    3. When reusing the rear door lock with motor assembly.


      1. A01HZTR

        Remove the door lock wiring harness seal from the rear door lock with motor assembly.

  15. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. A01I0X6

      Using a screwdriver, disengage the claw as shown in the illustration.

    2. A01I05X

      Remove the rear door lock remote control cable assembly.

  16. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. A01HZZU

      Using a screwdriver, disengage the 3 claws as shown in the illustration.

    2. A01HZG4

      Remove the rear door inside locking cable assembly.