VEHICLE STABILITY CONTROL SYSTEM VSC OFF Indicator Light Remains ON

DESCRIPTION

The skid control ECU is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch turns off TR(A)C operation and pressing and holding this switch turns off TR(A)C and VSC operation. If VSC operation is turned off, the VSC OFF indicator light will come on.

WIRING DIAGRAM

A01HXV9E01

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK CAN COMMUNICATION SYSTEM


    1. Check if a CAN communication system DTC is output Click here.

      Result
      Result Proceed to
      DTC is not output. A
      DTC is output. B

    B

    INSPECT CAN COMMUNICATION SYSTEM Click here

    A

  2. CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED


    1. Check if the skid control ECU connector is securely connected.

      OK
      The connector is securely connected.

    NG

    CONNECT CONNECTOR TO ECU CORRECTLY

    OK

  3. CHECK BATTERY


    1. Check the battery voltage.

      Standard Voltage
      11 to 14 V
      Result
      Result Proceed to
      OK A
      NG (for 2GR-FE) B
      NG (for 2AR-FE) C

    B

    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY Click here

    C

    CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY Click here

    A

  4. READ VALUE USING TECHSTREAM (VSC OFF SWITCH)


    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Select the Data List using the Techstream Click here.

      ABS/VSC/TRAC
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      TRAC/VSC Off Mode TR(A)C/VSC off mode / Normal, TRC OFF, Unknown or VSC OFF

      Normal: Normal mode

      TRC OFF: TR(A)C off mode

      Unknown: Unspecified

      VSC OFF: VSC off mode

      		 -

    4. Using the Techstream, check that the switch condition displayed on the Techstream changes according to VSC OFF switch operation.

      OK
      The Techstream display changes according to VSC OFF switch operation.

    NG

    INSPECT VSC OFF SWITCH Click here

    OK

  5. INSPECT COMBINATION METER ASSEMBLY


    1. Turn the ignition switch off.

    2. Perform an Active Test of the combination meter assembly (meter CPU) using the Techstream Click here.

    3. Check the combination meter assembly.

      OK
      The VSC OFF indicator light turns on or off in accordance with the Active Test operation.

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    NG

    REPLACE COMBINATION METER ASSEMBLY Click here

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here

  6. INSPECT VSC OFF SWITCH


    1. A01I0BRE01
      Text in Illustration
      *a

      Component without harness connected

      (VSC OFF Switch)

      Turn the ignition switch off.

    2. Disconnect the VSC OFF switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      6 (+) - 3 (E) Switch pushed in Below 1 Ω
      6 (+) - 3 (E) Switch not pushed in 10 kΩ or higher

    NG

    REPLACE VSC OFF SWITCH Click here

    OK

  7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH)


    1. Disconnect the skid control ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition

      A49-9 (CSW) - I130-6 (+)*1

      A94-9 (CSW) - I130-6 (+)*2

      		 Always Below 1 Ω

      A49-9 (CSW) - Body ground*1

      A94-9 (CSW) - Body ground*2

      		 Always 10 kΩ or higher
      I130-3 (E) - Body ground Always Below 1 Ω

      *1: for 2AR-FE (w/o Dynamic Radar Cruise Control System)

      *2: for 2AR-FE (w/ Dynamic Radar Cruise Control System), 2GR-FE

      Tech Tips

      If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts Click here.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    REPLACE BRAKE ACTUATOR ASSEMBLY Click here