AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P0715, P0717

DTC Code DTC Name
P0715 Input / Turbine Speed Sensor Circuit Malfunction
P0717 Input Speed Sensor Circuit No Signal

DESCRIPTION

This sensor detects the rotation speed of the turbine which shows the input revolution (speed) of the transaxle. By comparing the input turbine speed signal (NT) with the counter gear speed sensor signal (NC), the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, thus, providing smooth gear shifts.

A01I1HSE04
Text in Illustration
*1 Counter Gear *2 Clutch Drum
*3 Output Speed Sensor NC *4 Input Speed Sensor NT
DTC No. DTC Detection Condition Trouble Area
P0715 When the speed sensor input voltage is either more than 1.9 V or less than 0.1 V for 4.5 seconds or more.(1-trip detection logic)

  • Transmission revolution sensor (speed sensor NT)

  • Transmission wire

  • Wiring harness connector

  • ECM
P0717

ECM detects conditions (a), (b) and (c) continuously for 5 sec. or more: (1-trip detection logic)

(a) Vehicle speed: 50 km/h (31 mph) or more

(b) Park/neutral position switch (R) is OFF

(c) Speed sensor (NT): less than 300 rpm

MONITOR DESCRIPTION

The NT terminal of the ECM detects a revolution signal from the speed sensor (NT) (input RPM). The ECM calculates gear shifts comparing the speed sensor (NT) with the speed sensor (NC).

While the vehicle is operating in 2nd, 3rd, 4th or 5th gear with the shift lever in D, if the input shaft revolution (speed) is less than 300 rpm*1 although the output shaft revolution (speed) is more than 1000 rpm*2, the ECM interprets this as a fault, illuminates the MIL and stores the DTC.

*1: Pulse is not output or is irregularly output.

*2: The vehicle speed is 50 km/h (31 mph) or more.

MONITOR STRATEGY

Related DTCs

P0715: Speed sensor (NT)/Range check

P0717: Speed sensor (NT)/Verify pulse input
Required sensors/Components Speed sensor (NT), Speed sensor (NC)
Frequency of operation Continuous
Duration

P0715: 4.5 sec.

P0717: 5 sec.
MIL operation Immediate
Sequence of operation None

TYPICAL ENABLING CONDITIONS

P0715:
Battery voltage 8 V or more
Ignition switch ON
Starter OFF
P0717:
The monitor will run whenever this DTC is not present.

P0746, P0776, P0796, P2808 (Shift solenoid valve (functional))

P0748, P0778, P0798, P2810 (Shift solenoid valve (range))
Shift change Shift change is completed before starting next shift change operation
ECM selected gear 2nd, 3rd, 4th, 5th or 6th
Output shaft rpm 1,000 rpm or more
R switch OFF
NSW switch OFF
Engine Running
Battery voltage 8 V or more
Ignition switch ON
Starter OFF
Transmission range switch circuit Not malfunction
Turbine speed sensor range check Not malfunction

TYPICAL MALFUNCTION THRESHOLDS

P0715:
Sensor voltage Less than 0.1 V or more than 1.9 V
P0717:
Sensor signal rpm Less than 300 rpm

COMPONENT OPERATING RANGE

Speed sensor (NT) Turbine speed is equal to engine speed with lock-up ON

WIRING DIAGRAM

A01I1HTE01

INSPECTION PROCEDURE

Note

Perform the universal trip to clear permanent DTCs Click here.

Tech Tips

Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

Note

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, read the Data List.

    Engine and ECT
    Tester Display Measurement Item/Range Normal Condition Diagnostic Note
    SPD (NT)

    Input shaft speed/

    Min.: 0 rpm

    Max.: 12750 rpm

    Lock-up is


    • ON (after warming up engine): Input turbine speed (NT) is equal to engine speed

    • OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed

    		 Data is displayed in increments of 50 rpm

    Tech Tips


    • SPD (NT) is always 0 while driving: Open or short in the sensor or circuit.

    • SPD (NT) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (31 mph) or more: Sensor trouble, improper installation, or intermittent connection trouble of the circuit.

PROCEDURE


  1. INSPECT TRANSMISSION REVOLUTION SENSOR (SPEED SENSOR INSTALLATION)


    1. Remove the valve body assembly.

    2. A01HZ6T

      Make sure that the connector is properly connected, and check the speed sensor installation Click here.

      OK
      The installation bolt is tightened properly and there is no clearance between the sensor and transaxle case.

    NG

    REPAIR OR REPLACE TRANSMISSION REVOLUTION SENSOR Click here

    OK

  2. INSPECT TRANSMISSION WIRE


    1. A01I15PE17
      Text in Illustration
      *a

      Component without harness connected

      (Transmission Wire)
      *b Wiring Harness Connector Side
      *c Sensor Side

      Disconnect the speed sensor connector from the transmission wire.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 (NTB) sensor side - A-1 (NTB) wiring harness connector side Always Below 1 Ω
      2 (NTO) sensor side - A-2 (NTO) wiring harness connector side Always Below 1 Ω
      1 (NTB) sensor side - Body ground and other terminals Always 10 kΩ or higher
      2 (NTO) sensor side - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPLACE TRANSMISSION WIRE Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)


    1. Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E8-1 (NTB) - E26-116 (NTB) Always Below 1 Ω
      E8-2 (NTO) - E26-115 (NTO) Always Below 1 Ω
      E8-1 (NTB) or E26-116 (NTB) - Body ground and other terminals Always 10 kΩ or higher
      E8-2 (NTO) or E26-115 (NTO) - Body ground and other terminals Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT WIRING HARNESS CONNECTOR


    1. Remove the wiring harness connector.

    2. A01HYL9E01
      Text in Illustration
      *a

      Component without harness connected

      (Wiring Harness Connector)
      *b ECM Side
      *c Transmission Wire Side

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      E8-1 (NTB) - A-1 (NTB) Always Below 1 Ω
      E8-2 (NTO) - A-2 (NTO) Always Below 1 Ω
      E8-1 (NTB) - All other terminals Always 10 kΩ or higher
      E8-2 (NTO) - All other terminals Always 10 kΩ or higher
      Result
      Result Proceed to
      OK A
      NG (When not using the engine support bridge) B
      NG (When using the engine support bridge) C

    B

    REPLACE WIRING HARNESS CONNECTOR Click here

    C

    REPLACE WIRING HARNESS CONNECTOR Click here

    A

  5. REPLACE TRANSMISSION REVOLUTION SENSOR

    Click here


    NEXT

  6. CHECK IF DTC OUTPUT RECURS (SEE IF DTC P0715 AND/OR P0717 OUTPUT AGAIN)


    1. Connect the Techstream to the DLC3.

    2. Start the engine and turn the Techstream on.

    3. Clear the DTCs Click here.

      Tech Tips

      Write down the currently output DTCs before clearing them.

    4. Perform the monitor drive pattern Click here.

    5. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    6. Read the DTCs using the Techstream.

      Result
      Display (DTC Output) Proceed to
      Only "P0715 or P0717" is output A
      No output B

    B

    END

    A

    REPLACE ECM Click here