SHIFT LEVER INSTALLATION

INSTALL SHIFT LEVER SUPPORT
1. Install the shift lever support to the vehicle body with the 4 bolts in the order shown in the illustration.
  
  Torque:
  
  12 N*m { 122 kgf*cm, 9 ft.*lbf }

INSTALL LOWER SHIFT LEVER ASSEMBLY

Note

Check that the shift lever position sensor and shift lever are in neutral.

Install the lower shift lever assembly to the shift lever support with the 4 bolts in the order shown in the illustration.

Torque:

12 N*m { 122 kgf*cm, 9 ft.*lbf }
Engage the 2 clamps.
Connect the shift lock control ECU connector.

Text in Illustration
*1	Slider
*2	Lock Piece
*a	Slide
*b	Pull

Slide the slider of the transmission control cable assembly in the direction indicated by the arrow and pull the lock piece outward.

Engage the 2 claws to connect the transmission control cable assembly to the lower shift lever assembly.
Text in Illustration

*1 Lock Piece

Connect the end of the transmission control cable assembly to the lower shift lever assembly.
Note
- Check that the lock piece is pulled out.
- Connect the end of the transmission control cable assembly all the way to the base of the pin.
Push the lock piece into the adjuster case.
Note
- Check that the shift lever position sensor and shift lever are in neutral.
- Securely push in the lock piece until the slider lock is engaged.

INSTALL NO. 1 CONSOLE BOX DUCT
1. Install the No. 1 console box duct to the lower shift lever assembly with the clip.
INSTALL NO. 1 CONSOLE BOX MOUNTING BRACKET
1. Install the No. 1 console box mounting bracket to the lower shift lever assembly with the screw.
2. Engage the guide.
INSTALL FLOOR CARPET BRACKET LH
1. Engage the 2 guides.
2. Install the floor carpet bracket LH with the 2 clips.
INSTALL CONSOLE BOX INSERT
1. Engage the guide and 2 clips as shown in the illustration.
2. Install the console box insert with the screw <C> or <D>.
INSTALL FRONT NO. 2 CONSOLE BOX INSERT
1. Engage the guide and 2 clips as shown in the illustration.
2. Install the front No. 2 console box insert with the screw <C> or <D>.
3. Engage the 2 claws to connect the room temperature sensor.
INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY
1. Connect each connector.
2. Engage the guide and 2 clips as shown in the illustration.
3. Install the upper console panel sub-assembly with the 2 screws <C> or <D>.
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
1. Connect the connector.
2. Engage the glove compartment light as shown in the illustration.
3. Engage the clamp.
4. Engage the guide and 2 clips.
5. Install the lower instrument panel sub-assembly with the 5 screws <C> or <D>.

Text in Illustration
*1	Lock Piece

INSTALL LOWER NO. 2 INSTRUMENT PANEL AIRBAG ASSEMBLY

Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Text in Illustration
*1	Airbag Connector
*2	Airbag Connector Lock

Connect the airbag connector to the lower No. 2 instrument panel airbag assembly.

Note

When connecting any airbag connector, take care not to damage the airbag wire harness.

Push in the lock to install the airbag connector.
Temporarily install the lower No. 2 instrument panel airbag assembly with the 3 claws.
Install the 3 bolts.

Torque:

10 N*m { 102 kgf*cm, 7 ft.*lbf }

Note

Confirm that the lower No. 2 instrument panel airbag assembly is installed securely without any excessive gaps and is not protruding outward.

INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
1. Engage the 2 guides and 4 claws to install the No. 2 instrument panel under cover sub-assembly.
INSTALL INSTRUMENT SIDE PANEL RH
1. Engage the 3 guides.
2. Engage the 4 claws to install the instrument side panel RH as shown in the illustration.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
1. Text in Illustration
  
  *1 Alignment Mark (White)
  
  Align the alignment mark (White) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip RH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL FRONT DOOR SCUFF PLATE RH

Tech Tips

Use the same procedure as for the LH side.
INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY
1. Engage the 4 claws, 9 clips and 3 guides.
2. Install the lower No. 1 instrument panel finish panel assembly with the bolt <B> and screw <C> or <D>.
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
1. Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
INSTALL INSTRUMENT SIDE PANEL LH
1. Engage the 3 guides.
2. Engage the 4 claws to install the instrument side panel LH as shown in the illustration.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
1. Text in Illustration
  
  *1 Alignment Mark (Yellow)
  
  Align the alignment mark (Yellow) on the weatherstrip with the protruding portion on the body indicated by the arrow in the illustration, and install the front door opening trim weatherstrip LH.
  
  Note
  
  After installation, check that the corners fit correctly.
INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH
1. Engage the 2 clips.
2. Install the cowl side trim sub-assembly LH with the clip.
INSTALL FRONT DOOR SCUFF PLATE LH
1. Engage the 10 claws to install the front door scuff plate LH.
INSTALL REAR CONSOLE BOX ASSEMBLY

Click here
INSPECT SHIFT LEVER POSITION
1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.
2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.
CONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
PERFORM DIAGNOSTIC SYSTEM CHECK

Click here
INSPECT SRS WARNING LIGHT

Click here