PARK / NEUTRAL POSITION SWITCH INSTALLATION


  1. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    1. Move the shift lever to N.

    2. A01HYF4E11
      Text in Illustration
      *a Protrusion

      Align the protrusions of the park/neutral position switch.

    3. Install the park/neutral position switch to the control shaft with the 2 bolts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Note


      • Before installing the park/neutral position switch, remove any dirt or rust on the installation portion of the control shaft. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch cannot be reinstalled correctly.

      • After installing the park/neutral position switch, confirm that the 2 protrusions on the switch are aligned.

    4. Install the control shaft lever to the control shaft with the nut and washer.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

    5. Connect the connector to the park/neutral position switch.

  2. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


    1. Connect the transmission control cable assembly to the transmission control cable bracket with a new clip.

    2. Connect the transmission control cable assembly to the control shaft lever with the nut.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Before connecting the transmission control cable assembly, check that the park/neutral position switch and the shift lever are in neutral.

  3. INSTALL AIR CLEANER CASE SUB-ASSEMBLY


    1. A01HZL1E01
      Text in Illustration
      *1 Air Cleaner Case Sub-assembly
      *2 Inlet No. 1 Air Cleaner
      *a Projection
      *b Hole

      Install the air cleaner case sub-assembly to the inlet No. 1 air cleaner.

    2. Insert the projection of the air cleaner case sub-assembly to the hole of the air cleaner bracket as shown in the illustration.

    3. Install the 2 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

    4. Connect the wire harness clamp, connector, vacuum hose and No. 1 fuel vapor feed hose.

  4. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  5. INSTALL AIR CLEANER CAP SUB-ASSEMBLY


    1. Connect the air cleaner cap sub-assembly to the throttle with motor body assembly with the hose clamp.

    2. Install the air cleaner cap with hose to the air cleaner case with the 2 clamps.

    3. Connect the wire harness clamp and mass air flow meter connector.

    4. Connect the 3 hoses.

    5. Connect the ventilation hose.

    6. Connect the mass air flow meter connector and wire harness clamp.

  6. INSTALL INLET NO. 2 AIR CLEANER


    1. Install the inlet No. 2 air cleaner to the air cleaner case sub-assembly with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    2. Connect the 2 wire harness clamps and vacuum hose clamp.

  7. INSTALL COOL AIR INTAKE DUCT SEAL


    1. Install the cool air intake duct seal with the 9 clips.

  8. INSPECT PARK / NEUTRAL POSITION SWITCH ASSEMBLY


    1. A01I27EE05
      Text in Illustration
      *a

      Component without harness connected

      (Park/Neutral Position Switch)

      Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

      Standard Resistance
      Tester Connection Shift Lever Position Specified Condition

      1 (RB) - 3 (PL)

      4 (B) - 9 (L)

      		 P Below 1 Ω
      Except P 10 kΩ or higher
      1 (RB) - 2 (RL) R Below 1 Ω
      Except R 10 kΩ or higher

      1 (RB) - 8 (NL)

      4 (B) - 9 (L)

      		 N Below 1 Ω
      Except N 10 kΩ or higher
      1 (RB) - 7 (DL) D, S, "+" or "-" Below 1 Ω
      Except D, S, "+" and "-" 10 kΩ or higher

      If the result is not as specified, replace the park/neutral position switch assembly.

  9. INSPECT SHIFT LEVER POSITION


    1. When the shift lever is moved from P to R with the engine switch on (IG) and brake pedal depressed, make sure that the shift lever moves smoothly and correctly into position.

    2. Start the engine and make sure that the vehicle moves forward when the shift lever is moved from N to D and moves rearward when the shift lever is moved to R.

  10. ADJUST SHIFT LEVER POSITION


    1. Move the shift lever to N.

    2. Remove the console box Click here.

    3. A01HZD7

      Disconnect the end of the transmission control cable assembly from the lower shift lever assembly

    4. A01I0DKE03
      Text in Illustration
      *1 Slider
      *2 Lock Piece
      *a Slide
      *b Pull

      Slide the slider of the transmission control cable in the direction indicated by the arrow and pull the lock piece outward.

    5. A01I08HE01
      Text in Illustration
      *1 Lock Piece

      Install the end of the transmission control cable to the shift lever assembly.

      Note


      • Check that the lock piece is pulled up.

      • Install the cable end all the way to the base of the pin.

    6. Push the lock piece into the adjuster case.

      Note


      • Check that the park/neutral position switch and the shift lever are in neutral.

      • Securely push in the lock piece until the slider lock is engaged.

    7. After adjusting the shift lever position, check the operation and function of the shift lever. If there is a problem, adjust the position again.

    8. Install the console box Click here.