CRUISE CONTROL SYSTEM Cruise Control Switch Circuit

DESCRIPTION

The cruise control switch is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL.

WIRING DIAGRAM

A01I1NQE17

INSPECTION PROCEDURE

PROCEDURE


  1. READ VALUE ON TECHSTREAM

    A01HYF8E21
    Text in Illustration
    *a ON-OFF
    *b -/SET
    *c +/RES
    *d CANCEL

    1. Connect the Techstream to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the Techstream on.

    4. Select the following menu items: Powertrain / Cruise Control / Data List.

    5. Check the Data List to confirm proper functioning of the cruise control switch.

      Cruise Control
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Main SW M-CPU Cruise control switch signal (Main CPU) / ON or OFF

      ON: Cruise control switch (ON-OFF button) pushed

      OFF: Cruise control switch (ON-OFF button) released

      		 -
      Cancel Switch CANCEL switch signal / ON or OFF

      ON: CANCEL switch on

      OFF: CANCEL switch off

      		 -
      SET/COAST Switch -/SET switch signal / ON or OFF

      ON: -/SET switch on

      OFF: -/SET switch off

      		 -
      RES/ACC Switch +/RES switch signal / ON or OFF

      ON: +/RES switch on

      OFF: +/RES switch off

      		 -
      OK
      When the cruise control switch is operated, the display changes as shown above.

    NG

    INSPECT CRUISE CONTROL SWITCH Click here

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  2. INSPECT CRUISE CONTROL SWITCH


    1. Remove the cruise control switch Click here.

    2. Measure the resistance according to the value(s) in the table below.

      A01HYBCE19
      Standard Resistance
      Tester Connection Switch Condition Specified Condition
      1 - 3 Cruise control switch (ON-OFF button) released 1 MΩ or higher
      Cruise control switch (ON-OFF button) pushed Below 2.5 Ω
      +/RES switch ON 235 to 245 Ω
      -/SET switch ON 617 to 643 Ω
      CANCEL switch ON 1509 to 1571 Ω
      Text in Illustration
      *1 Cruise Control Switch (ON-OFF button) - -
      *a

      Component without harness connected

      (Cruise Control Switch)

      		 *b ON-OFF
      *c +/RES *d -/SET
      *e CANCEL - -

    NG

    REPLACE CRUISE CONTROL SWITCH Click here

    OK

  3. CHECK CRUISE CONTROL SWITCH WIRE


    1. A01I0B7E01
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Spiral Cable Sub-assembly)
      *b

      Front view of wire harness connector

      (to Cruise Control Switch)

      Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Specified Condition
      Cruise control switch side connector terminal 3 - z2-3 Below 1 Ω
      Cruise control switch side connector terminal 1 - z2-4 Below 1 Ω

    NG

    REPAIR OR REPLACE CRUISE CONTROL SWITCH WIRE

    OK

  4. CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Be sure to read the pages shown in the brackets.

    Tech Tips



    1. A01HZBSE02
      Text in Illustration
      *a

      Component without harness connected

      (Spiral Cable Sub-assembly)

      Remove the spiral cable sub-assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Spiral Cable Sub-assembly Position Specified Condition
      z2-3 - I28-1 (CCS) Center Below 3 Ω
      2.5 rotations to the left
      2.5 rotations to the right
      z2-4 - I28-2 (ECC) Center Below 3 Ω
      2.5 rotations to the left
      2.5 rotations to the right

    3. After setting the spiral cable sub-assembly to the center position, rotate the spiral cable sub-assembly 2.5 times clockwise. Then while rotating the spiral cable sub-assembly 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      z2-3 - I28-1 (CCS) Always Below 3 Ω
      z2-4 - I28-2 (ECC) Always Below 3 Ω

      Tech Tips

      The spiral cable sub-assembly makes a maximum of approximately 5 rotations.


    NG

    REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY Click here

    OK

  5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM AND BODY GROUND)


    1. Disconnect the ECM connector.

    2. Disconnect the spiral cable sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      for 2AR-FE
      Tester Connection Condition Specified Condition
      A25-47 (CCS) - I28-1 (CCS) Always Below 1 Ω
      for 2GR-FE
      Tester Connection Condition Specified Condition
      A25-47 (CCS) - I28-1 (CCS) Always Below 1 Ω
      Standard Resistance (Check for Short)
      for 2AR-FE
      Tester Connection Condition Specified Condition
      A25-47 (CCS) or I28-1 (CCS) - Body ground Always 10 kΩ or higher
      for 2GR-FE
      Tester Connection Condition Specified Condition
      A25-47 (CCS) or I28-1 (CCS) - Body ground Always 10 kΩ or higher

    4. Reconnect the spiral cable sub-assembly connector.

    5. Reconnect the ECM connector.


    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - ECM)

    OK

  6. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)


    1. Disconnect the spiral cable sub-assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance (Check for Open)
      Tester Connection Condition Specified Condition
      I28-2 (ECC) - Body ground Always Below 1 Ω
      Result
      Result Proceed to
      OK (for 2AR-FE) A
      OK (for 2GR-FE) B
      NG C

    3. Reconnect the spiral cable sub-assembly connector.


    B

    REPLACE ECM Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - BODY GROUND)

    A

    REPLACE ECM Click here