ENGINE SWITCH REMOVAL


  1. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work Click here.

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)

    Click here.

  4. REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)

    Click here.

  5. REMOVE FRONT DOOR SCUFF PLATE LH


    1. A01I27F

      Disengage the 10 claws and remove the front door scuff plate LH.

  6. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    1. A01I1YY

      Remove the clip.

    2. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.

  7. DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. A01HZ7V

      Disconnect the front door opening trim weatherstrip LH.

  8. REMOVE INSTRUMENT SIDE PANEL LH


    1. A01I23L

      Using a moulding remover, disengage the 4 claws as shown in the illustration.

    2. A01HZF4

      Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.

  9. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    1. A01HXFQ

      Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.

  10. REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01HXUME01
      Text in Illustration
      *a Protective Tape

      Apply protective tape to the area shown in the illustration.

    2. A01HXSO

      Disengage the 2 clips as shown in the illustration.

    3. A01HYOX

      Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.

  11. REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY


    1. Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.

    2. A01I1J7

      Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.

    3. A01HXM9

      Disengage the 5 claws, 5 clips and 2 guides.

    4. Disconnect each connector.

    5. A01I20W

      Remove the instrument cluster finish panel assembly as shown in the illustration.

  12. DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY


    1. A01I14J

      Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.

  13. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01I26P

      Remove the bolt <B> and screw <C> or <D>.

    2. A01HZC8

      Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.

  14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY


    1. A01I1CN

      Disengage the 4 clips to remove the lower instrument panel finish panel assembly.

    2. w/ Smart Key System:


      1. Disconnect the connector.

  15. REMOVE ENGINE SWITCH


    1. A01I0V5

      Disengage the 2 claws and remove the engine switch.