ВЫПУСКНОЙ КОЛЛЕКТОР УСТАНОВКА

PROCEDURE


  1. INSTALL AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

    Click here

  2. INSTALL AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

    Click here

  3. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH


    1. B001W8SC02
      *1 No. 2 Air Tube
      *a Front
      *b Tab
      *c Claw

      w/ Secondary Air Injection System:


      1. Install a new gasket to the cylinder head and a new gasket to the No. 2 air tube.

        Tech Tips


        • Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.

        • Install the air tube gasket with the gasket claws facing the No. 2 air tube side.

      2. B001W3DE02

        Temporarily install the exhaust manifold sub-assembly RH with the 2 nuts labeled A and 8 new nuts.

      3. Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.

        Torque:
        for nut A
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
        except nut A
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. B00202IC01
      *a Front
      *b Tab

      w/o Secondary Air Injection System:


      1. Install a new gasket to the cylinder head.

        Tech Tips

        Install the exhaust manifold gasket with the gasket tab facing toward the front of the engine.

      2. Temporarily install the exhaust manifold sub-assembly RH with the 8 new nuts.

      3. Uniformly tighten the 8 nuts.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      4. Attach the wire harness clamp to the bracket and connect the connector.

  4. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    1. Install the No. 1 exhaust manifold heat insulator with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  5. INSTALL NO. 1 MANIFOLD STAY


    1. Temporarily install the No. 1 manifold stay with the 3 bolts.

    2. B001WV3E03

      Tighten the 3 bolts in the order shown in the illustration.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  6. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH


    1. B001W2CC02
      *1 No. 3 Air Tube
      *a Front
      *b Tab
      *c Claw

      w/ Secondary Air Injection System:


      1. Install a new gasket to the cylinder head and a new gasket to the No. 3 air tube.

        Tech Tips


        • Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.

        • Install the air tube gasket with the gasket claws facing the No. 3 air tube side.

      2. B001ZG8E01

        Temporarily install the exhaust manifold with the 2 nuts labeled A and 8 new nuts.

      3. Uniformly tighten the nuts that are not labeled A, and then tighten the 2 nuts labeled A.

        Torque:
        for nut A
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
        except nut A
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }
    2. B001XPSC01
      *a Front
      *b Tab

      w/o Secondary Air Injection System:


      1. Install a new gasket to the cylinder head.

        Tech Tips

        Install the exhaust manifold gasket with the gasket tab facing toward the rear of the engine.

      2. Temporarily install the exhaust manifold sub-assembly LH with the 8 new nuts.

      3. Uniformly tighten the 8 nuts.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      4. Attach the wire harness clamp to the bracket and connect the connector.

  7. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR


    1. Install the No. 2 exhaust manifold heat insulator with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  8. INSTALL NO. 2 MANIFOLD STAY


    1. Temporarily install the No. 2 manifold stay with the 3 bolts.

    2. B001XWYE02

      Tighten the 3 bolts in the order shown in the illustration.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  9. INSTALL PROPELLER SHAFT HEAT INSULATOR


    1. Install the propeller shaft heat insulator with the 2 bolts.

      Torque:
      16 N*m  { 160 kgf*cm, 12 ft.*lbf }

  10. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  11. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

    Click here

  12. INSTALL CENTER EXHAUST PIPE ASSEMBLY

    Click here

  13. INSTALL TAILPIPE ASSEMBLY

    Click here

  14. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  15. INSPECT FOR EXHAUST GAS LEAK

    If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

  16. INSTALL FRONT FENDER APRON SEAL LH


    1. Install the front fender apron seal LH with the 3 clips.

  17. INSTALL FRONT FENDER APRON SEAL REAR LH


    1. Install the front fender apron seal rear LH with the 4 clips.

  18. INSTALL FRONT FENDER APRON SEAL FRONT RH


    1. Install the front fender apron seal front RH with the 3 clips.

  19. INSTALL FRONT FENDER APRON SEAL REAR RH


    1. Install the front fender apron seal rear RH with the 4 clips.

  20. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

    Click here

  21. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

    Click here

  22. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

    Click here

  23. INSTALL NO. 2 ENGINE UNDER COVER

    Click here