ДВИГАТЕЛЬ В СБОРЕ УСТАНОВКА

PROCEDURE


  1. INSTALL NO. 2 FRONT ENGINE MOUNTING BRACKET LH


    1. Install the No. 2 front engine mounting bracket LH with the bolt.

      Torque:
      32 N*m  { 326 kgf*cm, 24 ft.*lbf }

  2. INSTALL FRONT ENGINE MOUNTING INSULATOR RH


    1. Install the mounting insulator with the nut.

      Torque:
      72 N*m  { 734 kgf*cm, 53 ft.*lbf }

  3. INSTALL FRONT ENGINE MOUNTING INSULATOR LH


    1. Install the mounting insulator with the nut.

      Torque:
      72 N*m  { 734 kgf*cm, 53 ft.*lbf }

  4. REMOVE ENGINE STAND


    1. B001ZEA

      Install 2 engine hangers with 2 bolts as shown in the illustration.

      Torque:
      43 N*m  { 438 kgf*cm, 32 ft.*lbf }

      Tech Tips

      Engine hanger 12281-38150
      Bolt 90119-14120

    2. Attach an engine sling device and hang the engine with a chain block.

    3. Remove the bolts and engine assembly from the engine stand.

      Note


      • With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

      • Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

  5. INSTALL ENGINE ASSEMBLY


    1. Slowly lower the engine assembly into the engine compartment.

      Note

      Make sure that the engine is clear of all wiring and hoses.

    2. Attach the engine mounting insulators to the vehicle.

    3. Install the 4 engine mounting insulator bolts.

      Torque:
      79 N*m  { 806 kgf*cm, 58 ft.*lbf }

    4. Remove the 2 bolts and 2 engine hangers.

  6. INSTALL WATER PIPE AND HOSE SUB-ASSEMBLY


    1. Connect the hose and install the water pipe and hose with the 2 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

  7. CONNECT OIL COOLER PIPE ASSEMBLY


    1. Connect the oil cooler pipe with the 2 bolts.

      Torque:
      14 N*m  { 143 kgf*cm, 10 ft.*lbf }

  8. INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY


    1. B001X5AE07

      Using SST, hold the crankshaft.

      SST
      09213-70011
      09330-00021
    2. B001WJC

      Install the crankshaft angle sensor rotor.

      Text in Illustration
      B001XPG Engine Side

      Tech Tips


      • Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

      • As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.

    3. B001WKTE01
      Text in Illustration
      *1 Drive Plate
      *2 Rear Drive Plate Spacer
      B001XPG Automatic Transmission Side

      Install the drive plate and rear drive plate spacer onto the crankshaft.

      Tech Tips

      As the rear drive plate spacer and the drive plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.

    4. Install the drive plate and ring gear and bolts.

      Tech Tips

      The bolts are tightened in 2 progressive steps.


      1. Clean the bolts and bolt holes.

      2. B001WHFE03
        Text in Illustration
        *1 Adhesive

        Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

        Adhesive
        Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      3. B001YJEE02

        Step 1:

        Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

        Torque:
        30 N*m  { 301 kgf*cm, 22 ft.*lbf }

        Note


        • Do not reuse the drive plate installation bolts.

        • Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.

      4. Mark the upside of each drive plate installation bolt with paint.

      5. Step 2:

        Tighten the cylinder head bolts another 90°.

      6. Check that the painted marks are now at a 90° angle to the upside.

        Note

        Do not start the engine for at least an hour after installing the drive plate.

  9. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

    Tech Tips

    Only perform this procedure when replacement of the engine mounting insulator is necessary.


    1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

      Torque:
      59 N*m  { 602 kgf*cm, 44 ft.*lbf }

    2. Install the front engine mounting insulator RH with the 2 bolts.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  10. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

    Click here

  11. INSTALL STARTER ASSEMBLY

    Click here

  12. INSTALL STARTER COVER

    Click here

  13. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

    Click here

  14. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  15. INSTALL NO. 1 MANIFOLD STAY

    Click here

  16. INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

    Click here

  17. INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  18. INSTALL NO. 2 MANIFOLD STAY

    Click here

  19. INSTALL PROPELLER SHAFT HEAT INSULATOR

    Click here

  20. INSTALL REAR PROPELLER SHAFT ASSEMBLY

    Click here

  21. INSTALL FRONT PROPELLER SHAFT ASSEMBLY

    Click here

  22. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Apply a light coat of engine oil to a new O-ring.

    2. Install the O-ring to the guide.

    3. Install the dipstick guide with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    4. Install the dipstick.

    5. Connect the wire harness clamp.

  23. INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  24. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

    Click here

  25. INSTALL CENTER EXHAUST PIPE ASSEMBLY

    Click here

  26. INSTALL TAILPIPE ASSEMBLY

    Click here

  27. INSTALL GENERATOR ASSEMBLY

    Click here

  28. CONNECT VANE PUMP ASSEMBLY

    Click here

  29. CONNECT COOLER COMPRESSOR ASSEMBLY

    Click here

  30. CONNECT WIRE HARNESS AND HOSE


    1. w/ Winch:

      Attach the wire harness clamp and connect the ground wire to the wire harness clamp bracket with the nut.

      Torque:
      19 N*m  { 195 kgf*cm, 14 ft.*lbf }

    2. Connect the 2 connectors and 2 clamps.

    3. Connect the 2 connectors and 2 clips to the engine room junction block.

    4. Install the engine wire to the engine room junction block with the nut. Then connect the 2 clips.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Install the ground wire to the body with the bolt.

      Torque:
      8.4 N*m  { 86 kgf*cm, 74 in.*lbf }

    6. Connect the clamp.

    7. Connect the cable to the positive (+) battery terminal.

    8. Install the wire to the positive (+) battery cable with the nut.

      Torque:
      7.6 N*m  { 77 kgf*cm, 67 in.*lbf }

    9. Install the ground wire with the bolt.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    10. Connect the clip and 5 connectors to the connector holder block.

    11. Install the heater hose.

    12. Connect the ECM connector and clamp.

      Tech Tips

      Refer to the following procedures to connect the ECM connector Click here.

    13. Connect the purge line hose.

  31. CONNECT FUEL MAIN AND RETURN HOSE


    1. Connect the fuel main and return hoses Click here.

    2. Install the fuel pipe clamp.

  32. INSTALL RADIATOR ASSEMBLY

    Click here

  33. INSTALL FAN SHROUD

    Click here

  34. INSTALL NO. 2 RADIATOR HOSE

  35. INSTALL NO. 1 RADIATOR HOSE

  36. INSTALL AIR CLEANER ASSEMBLY


    1. Install the air cleaner with the 3 bolts.

      Torque:
      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

  37. INSTALL AIR CLEANER HOSE ASSEMBLY

    Click here

  38. ADD ENGINE OIL

    Click here

  39. ADD ENGINE COOLANT

    Click here

  40. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  41. INSPECT FOR OIL LEAK

    Click here

  42. INSPECT FOR COOLANT LEAK

    Click here

  43. INSPECT FOR EXHAUST GAS LEAK

    Click here

  44. INSPECT FOR FUEL LEAK

    Click here

  45. INSPECT SHIFT LEVER POSITION

    Click here

  46. INSTALL V-BANK COVER SUB-ASSEMBLY


    1. B001YPCE05
      Text in Illustration
      *1 Bracket
      *2 Hook
      *3 Pin
      *4 Grommet

      Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.

  47. INSTALL OIL PAN PROTECTOR ASSEMBLY

    Click here

  48. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 2 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  49. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    1. Install the No. 1 engine under cover with the 10 bolts.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }

  50. INSTALL FRONT FENDER APRON SEAL REAR RH

    Click here

  51. INSTALL FRONT FENDER APRON SEAL FRONT RH

    Click here

  52. INSTALL FRONT FENDER APRON SEAL REAR LH

    Click here

  53. INSTALL FRONT FENDER APRON SEAL LH

    Click here

  54. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

    Click here

  55. INSTALL HOOD SUB-ASSEMBLY


    1. Install the hood with the 4 bolts.

      Torque:
      13 N*m  { 133 kgf*cm, 10 ft.*lbf }

    2. Connect the 2 hood supports with the 2 hood support bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }

      CAUTION:

      Install the hood support while supporting the hood by hand.

      Note

      Check that the hood support is engaged in the ball joint and that it cannot be pulled out.

  56. ADJUST HOOD SUB-ASSEMBLY

    Click here

  57. INSTALL RADIATOR SIDE DEFLECTOR LH

    Click here

  58. INSTALL TRANSMISSION OIL COOLER AIR DUCT

    Click here

  59. INSTALL FRONT BUMPER COVER


  60. INSPECT IGNITION TIMING

    Click here

  61. INSPECT ENGINE IDLE SPEED

    Click here

  62. INSPECT CO/HC

    Click here

  63. INSPECT ENGINE OIL LEVEL

    Click here

  64. INSPECT ENGINE COOLANT LEVEL

    Click here