Click here

СИСТЕМА SFI (для моделей с вспомогательной системой подачи воздуха в нейтрализатор), Diagnostic DTC:P0724

Click here
Click here
DTC Code DTC Name
P0724 Brake Switch "B" Circuit High
Click here

DESCRIPTION

The stop light switch is part of a duplex system that transmits 2 signals: STP and ST1-. These 2 signals are used by the ECM to monitor whether or not the brake system is working properly. This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch remains on even when the vehicle is driven in a GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic).

  • Short in stop light switch signal circuit

  • Stop light switch assembly

  • ECM
Click here

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains on. When the stop light switch remains on during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be stored.

Click here

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).

  4. Turn the engine switch off and wait for at least 30 seconds.

  5. Turn the engine switch on (IG) and turn the GTS on [A].

  6. Wait 5 seconds.

  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].

  8. Read the pending DTCs.

    Tip:

    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  10. Input the DTC: P0724.

  11. Check the DTC judgment result.

    Tester Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit
    Tip:

    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].

  12. Start the engine [C].

  13. Accelerate the vehicle to 30 km/h (18.65 mph) or more, and then depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.

    CAUTION:

    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Check the DTC judgment result [E].

Click here

WIRING DIAGRAM

Refer to DTC P0504 (Click here).

Click here

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

Tip:

Using the GTS, the Data List item "Stop Light Switch" can be read.

Item

Measurement Item/

Range (Display)

 Normal Condition Diagnostic Note
Stop Light Switch

Stop light switch status/

ON or OFF

  • Brake pedal depressed: ON

  • Brake pedal released: OFF

 -
Click here

PROCEDURE


  1. Click here

    READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Connect the GTS to the DLC3.

    2. Turn the engine switch on (IG) and turn the GTS on.

    3. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

    4. Read the values displayed on the GTS.

      OK
      Item Measurement Item: Range (display) Normal Condition
      Stop Light Switch

      Stop light switch status:

      ON or OFF

      • ON: Brake pedal is depressed

      • OFF: Brake pedal is released

  2. Click here

    CHECK STOP LIGHT SWITCH ASSEMBLY INSTALLATION


    1. Check the stop light switch assembly installation.

      OK
      Stop light switch assembly is installed correctly.

  3. Click here

    READ VALUE USING GTS (STOP LIGHT SWITCH)


    1. Disconnect the stop light control relay assembly connector.

    2. Connect the GTS to the DLC3.

    3. Turn the engine switch on (IG) and turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

    5. Read the values displayed on the GTS.

      OK
      Item Measurement Item: Range (display) Normal Condition
      Stop Light Switch

      Stop light switch status:

      ON or OFF

      • ON: Brake pedal is depressed

      • OFF: Brake pedal is released

    • OK

      REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY

    • NGClick here
  4. Click here

    CHECK STOP LIGHT SWITCH ASSEMBLY


    1. Check the stop light switch assembly (Click here).


  5. Click here

    CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)


    1. Disconnect the stop light switch assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the Resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Brake Pedal Operation Specified Condition
      A73-4 (L) - A38-8 (ST1-) Always Below 1 Ω
      A73-2 (L) - A38-7 (STP) Always Below 1 Ω
      A73-4 (L) or A38-8 (ST1-) - Body ground Always 10 kΩ or higher
      A73-2 (L) or A38-7 (STP) - Body ground Always 10 kΩ or higher

    • OKClick here
    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - STOP LIGHT CONTROL RELAY)


    1. Disconnect the stop light switch assembly connector.

    2. Disconnect the stop light control relay assembly connector.

    3. Measure the Resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Brake Pedal Operation Specified Condition
      A73-1 (B) - A39-6 (+B) Always Below 1 Ω
      A73-2 (L) - A39-2 (STP) Always Below 1 Ω
      A73-1 (B) or A39-6 (+B) - Body ground Always 10 kΩ or higher
      A73-2 (L) or A39-2 (STP) - Body ground Always 10 kΩ or higher

    • OK

      REPLACE ECM (Click here)

    • NG

      REPAIR OR REPLACE HARNESS OR CONNECTOR