OUTER REAR VIEW MIRROR DISASSEMBLY

CAUTION / NOTICE / HINT

PROCEDURE

1. Click here

   REMOVE OUTER MIRROR LH

   Click here

2. Click here

   REMOVE OUTER MIRROR COVER

   Tip:

   Be sure to detach the claws of the outer mirror cover in the order shown in the illustration.

   
   
   1. 

      Using 2 screwdrivers, detach the 2 claws.

      Tip:

      Tape the screwdriver tip before use.

      Table 1. Text in Illustration

      *1	Protective Tape

   2. 

      Insert a screwdriver into the slot as shown in the illustration and push on the outer mirror body to create a space between the outer mirror body and outer mirror cover.

      Note:

      Be careful not to break the ribs.

      Tip:

      Tape the screwdriver tip before use.

      Table 2. Text in Illustration

      *1	Protective Tape	*2	Rib
      *a	Inner Side of Outer Mirror Cover	-	-

   3. 

      Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

      Tip:

      Tape the moulding remover before use.

      Table 3. Text in Illustration

      *1	Protective Tape

   4. Insert a moulding remover into the space made between the outer mirror body and outer mirror cover.

      Note:

      Do not insert the moulding remover more than 4 mm (0.157 in.).

      Standard
      Area Specified Condition a 4mm

   5. 

      Slide the moulding remover downwards as shown in the illustration to detach the 2 claws.

      Note:
      

      • Do not insert the moulding remover more than 4 mm (0.157 in.).

      • Do not slide the moulding remover past the point approximately 40 mm (1.57 in.) from the bottom edge of the outer mirror cover as the outer mirror body will become damaged.

      Table 4. Text in Illustration

      *1	Protective Tape

      Standard
      Area Specified Condition a 40mm b 4mm

   6. Remove the moulding remover B.

   7. 

      Apply protective tape to the areas of the body cover and outer mirror cover as shown in the illustration.

      Table 5. Text in Illustration

      *1	Protective Tape
      *a	Lower Side

   8. Insert a moulding remover B between the outer mirror cover and outer mirror body as shown in the illustration and detach the claw.

   9. 

      Using a screwdriver, detach the claw.

      Table 6. Text in Illustration

      *1	Protective Tape

   10. 

       Detach the 2 claws and remove the outer mirror cover.

       Note:

       When removing the cover, be careful not to damage the side turn signal light assembly or cover.

3. Click here

   REMOVE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

   Click here

4. Click here

   REMOVE SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)

   
   

   1. Remove the gasket

      
      

      1. Remove the tape.

      2. 

         Detach the 9 guides and remove the gasket.

         Tip:

         Slightly lower the gasket so that the television camera assembly can be removed.

   2. Remove the lower mirror cover

      
      
      1. 

         Using a screwdriver with its tip wrapped in protective tape, disconnect the 4 claws and remove the lower mirror cover.

         Table 7. Text in Illustration

         *1	Protective Tape

   3. Remove the base

      
      

      1. Remove the wire harness.

      2. 

         Using "TORX" socket wrench T25, remove the 3 screws.

         Note:

         Make sure to replace the "TORX" screws with new ones.

      3. Disconnect the guide and remove the base.

   4. 

      Detach the connector from the wire clip.

   5. 

      Using a screwdriver, disconnect the connector.

      Tip:

      Tape the moulding remover before use.

      Table 8. Text in Illustration

      *1	Protective Tape

   6. Remove the body

      
      
      1. 

         Remove the 5 screws and body.

   7. Remove the body

      
      
      1. 

         Disconnect the 2 guides and remove the body.

         Note:

         Be careful not to break the guide shown in the part of the illustration labeled A.

   8. 

      Remove the 3 screws and side television camera.