OUTER MIRROR SWITCH INSPECTION

PROCEDURE


  1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

    A01X9D7E08
    *1 Component without harness connected: (Outer Mirror Switch)

    1. Inspect the outer mirror switch assembly.


      1. Select "L" on the left/right adjustment switch.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition

        3 (MLV) - 4 (B)

        7 (M+) - 8 (E)

        		 Up Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        3 (MLV) - 8 (E)

        7 (M+) - 4 (B)

        		 Down Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        9 (MLH) - 4 (B)

        7 (M+) - 8 (E)

        		 Left Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        9 (MLH) - 8 (E)

        7 (M+) - 4 (B)

        		 Right Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

      3. Select "R" on the left/right adjustment switch.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Condition Specified Condition

        2 (MRV) - 4 (B)

        7 (M+) - 8 (E)

        		 Up Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        2 (MRV) - 8 (E)

        7 (M+) - 4 (B)

        		 Down Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        10 (MRH) - 4 (B)

        7 (M+) - 8 (E)

        		 Left Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        10 (MRH) - 8 (E)

        7 (M+) - 4 (B)

        		 Right Pressed Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Inspect the switch illumination.


      1. Apply battery voltage between the terminals of the light, and check the operation of the light.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 5 (ILL+)

        Battery negative (-) → Terminal 6 (ILL-)

        		 Light comes on

        If the result is not as specified, replace the outer mirror switch assembly.

  2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

    A01X9D7E09
    *1 Component without harness connected: (Outer Mirror Switch)

    1. Inspect the outer mirror switch assembly.


      1. Select "L" on the left/right adjustment switch.

      2. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        8 (MSW) - 9 (E) L switch L position 10 kΩ or higher
        Neutral position 10 kΩ or higher
        7 (M+) - 9 (E) Up Pressed 95 to 105 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Down Pressed 446 to 493 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Left Pressed 760 to 840 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Right Pressed 237 to 262 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

      3. Select "R" on the left/right adjustment switch.

      4. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        8 (MSW) - 9 (E) R switch R position Below 1 Ω
        Neutral position 10 kΩ or higher
        7 (M+) - 9 (E) Up Pressed 95 to 105 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Down Pressed 446 to 493 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Left Pressed 760 to 840 Ω
        Not pressed 10 kΩ or higher
        7 (M+) - 9 (E) Right Pressed 237 to 262 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the outer mirror switch assembly.

    2. Inspect the switch illumination.


      1. Apply battery voltage between the terminals of the light, and check the operation of the light.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 5 (ILL+)

        Battery negative (-) → Terminal 6 (ILL-)

        		 Light comes on

        If the result is not as specified, replace the outer mirror switch assembly.

  3. INSPECT RETRACTABLE OUTER MIRROR SWITCH (w/ Retract Mirror)


    1. A01X7DCE05

      Inspect the retractable outer mirror switch.


      1. Measure the resistance according to the value(s) in the table below.

        Standard Resistance
        Tester Connection Switch Condition Specified Condition
        5 (E) - 6 (MR)

        Pressed

        (Retracts)

        		 Below 1 Ω
        Not pressed 10 kΩ or higher

        If the result is not as specified, replace the retractable outer mirror switch.

    2. Inspect the switch illumination.


      1. Apply battery voltage between the terminals of the light, and check the operation of the light.

        OK
        Measurement Condition Specified Condition

        Battery positive (+) → Terminal 8 (ILL+)

        Battery negative (-) → Terminal 7 (ILL-)

        		 Light comes on

        If the result is not as specified, replace the retractable outer mirror switch.